Cisco CISCO3725 Guida di Installazione

Quick Start GuideCisco 3725 Modular RouterINCLUDING LICENSE AND WARRANTY1 Cisco 90-Day Limited Hardware Warranty Terms2 Documents, Equipment, and Tool

10The rack-mounting brackets are shown in Figure 1.Note The slots in the brackets marked RIGHT are for securing cables with cable ties.Figure 1 Rack-M

11Figure 3 Bracket Installation for Center Mounting with Rear Panel ForwardFigure 4 Bracket Installation for Front MountingFigure 5 Bracket Installati

12Grounding the ChassisYou must connect the chassis to a reliable earth ground; the ground wire must be installed in accordance with local electricals

13System Management ConnectionsThe connections described in Table 1 provide system management access.Power ConnectionsWarningRead the installation ins

14Note For installations compliant with the National Electric Code, AWG 14 (2.0 mm2) wire is required for DC input andsafety ground wire.Wiring Proced

15Figure 8 DC Power ConnectionsStep 5 Install the plastic cover over the terminal block. (See Figure 9.)WarningThe safety cover is an integral part of

16Figure 10 Connecting to One Source Only—Source A or Source BIn Figure 11, source A and source B share common negative terminal connections.Figure 11

17Figure 12 Connecting Source A and Source B with Common Positive TerminalsIn Figure 13, source A and source B are wired with opposite polarity ground

18WAN, LAN, and Voice ConnectionsThe connections and cables listed here are described in detail in the following documents:• Cisco 3700 Series Routers

19• Power and interface cables are connected.• Your PC terminal emulation program is configured for 9600 baud, 8 data bits, 1 stop bit, and no parity.

21 Cisco 90-Day Limited Hardware Warranty TermsThere are special terms applicable to your hardware warranty and various services that you can use duri

20Use ctrl-c to abort configuration dialog at any prompt.Default settings are in square brackets '[]'.Would you like to enter the initial co

21Would you like to enter the initial configuration dialog? [yes/no]:The setup command facility prompts you for basic information about your router an

22Current interface summaryAny interface listed with OK? value "NO" does not have a valid configurationInterface IP-Address

23Initial Configuration Using the CLI (Manual Configuration)This section shows how to bring up a command-line interface (CLI) prompt for configuration

247 Interface NumberingEach individual interface (port) on a Cisco 3725 router is identified by number as described in the following sections.WAN and

25Note The slot number for all WIC interfaces is always 0. (The W0 and W1 slot designations are for physical slot identificationonly.) Interfaces in t

269 Obtaining DocumentationCisco documentation and additional literature are available on Cisco.com. Cisco also provides several ways to obtain techni

27Access to all tools on the Cisco Technical Support Website requires a Cisco.com user ID and password. If you have a valid servicecontract but do not

28• The Cisco Product Catalog describes the networking products offered by Cisco Systems, as well as ordering and customersupport services. Access the

29

32 Documents, Equipment, and ToolsUser DocumentationAll the documents referenced in this quick start guide are available online on Cisco.com. To be su

30

31

Corporate HeadquartersCisco Systems, Inc.170 West Tasman DriveSan Jose, CA 95134-1706USAwww.cisco.comTel: 408 526-4000800 553-NETS (6387)Fax: 408 526-

4Warning DefinitionWarningIMPORTANT SAFETY INSTRUCTIONSThis warning symbol means danger. You are in a situation that could cause bodily injury. Before

5AvvertenzaIMPORTANTI ISTRUZIONI SULLA SICUREZZAQuesto simbolo di avvertenza indica un pericolo. La situazione potrebbe causare infortuni allepersone.

6AvisoINSTRUÇÕES IMPORTANTES DE SEGURANÇAEste símbolo de aviso significa perigo. Você se encontra em uma situação em que há risco de lesõescorporais.

7AdvarselVIGTIGE SIKKERHEDSANVISNINGERDetteadvarselssymbol betyderfare.Dubefinderdig iensituation med risikoforlegemesbeskadigelse.Før du begynder arb

8WarningThis unit is intended for installation in restricted access areas. A restricted access area can be accessed onlythrough the use of a special t

9WarningThis equipment must be grounded. Never defeat the ground conductor or operate the equipment in the absence ofa suitably installed ground condu