Cisco 3526 Specifiche Pagina 101
- Pagina / 130
- Indice
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
5-15
PA-MC-2T3+ Multi-Channel T3 Port Adapter Installation and Configuration
OL-3526-05
Chapter 5 Configuring Channelized mode for the Cisco PA-MC-2T3+
Configuring a Channelized T3 Link
Router(config)# controller T3 1/0/0
Router(config-controller)# t1 1 loopback network line
The example that follows is for a port adapter in slot 1 of the Cisco 7200 series routers:
Router# configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)# controller T3 1/0
Router(config-controller)# t1 1 loopback network line
In the preceding examples, network line loopback loops the data back toward the network (before
the T1 framer).
• Set the first T1 line into network payload loopback.
The example that follows is for a port adapter on a VIP in interface processor slot 1:
Router# configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)# controller T3 1/0/0
Router(config-controller)# t1 1 loopback network payload
The example that follows is for a port adapter in slot 1 of the Cisco 7200 series routers:
Router# configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)# controller T3 1/0
Router(config-controller)# t1 1 loopback network payload
In the preceding examples, network payload loopback loops just the payload data back toward the
network at the T1 framer.
Examples of the loopback remote command follow:
• Set the first T1 line into remote line inband loopback.
The example that follows is for a port adapter on a VIP in interface processor slot 1:
Router# configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)# controller T3 1/0/0
Router(config-controller)# t1 1 loop remote line inband
The example that follows is for a port adapter in slot 1 of the Cisco 7200 series routers:
Router# configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)# controller T3 1/0
Router(config-controller)# t1 1 loop remote line inband
In the preceding examples, remote line inband loopback sends a repeating five-bit in-band pattern
(of 00001) to the remote end, requesting that it enter into a network line loopback.
• Set the first T1 line into remote line FDL ANSI loopback.
The example that follows is for a port adapter on a VIP in interface processor slot 1:
Router# configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)# controller T3 1/0/0
Router(config-controller)# t1 1 loop remote line fdl ansi
The example that follows is for a port adapter in slot 1 of the Cisco 7200 series routers:
Router# configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
- Text Part Number: OL-3526-05 1
- CONTENTS 3
- Contents 4
- Document Revision History 7
- Objectives 8
- Organization 8
- Related Documentation 8
- Obtaining Documentation 10
- Documentation Feedback 11
- Submitting a Service Request 13
- Overview 17
- Channelized T3 Overview 18
- Unchannelized T3 Overview 18
- T3 Specifications 19
- Table 1-3 PA-MC-2T3+ LEDs 20
- Chapter 1 Overview 21
- Port adapter slot 23
- RX CELLS 24
- RX CARRIER 24
- RX ALARM 24
- VIP Slot Numbering 25
- VIP Interface Addresses 29
- Preparing for Installation 31
- Safety Guidelines 33
- Waarschuwing 34
- Varoitus 34
- Attention 35
- Figyelem! 35
- Avvertenza 35
- Advarsel 36
- ¡Advertencia! 36
- Varning! 36
- Safety Guidelines 37
- FCC Class A Compliance 39
- FCC Class A Compliance 40
- Handling Port Adapters 41
- Online Insertion and Removal 42
- Warnings and Cautions 43
- Cisco 7200 45
- ENHANCED ATM 51
- ROUTE SWITCH PROCESSOR 52
- Cables and Connectors 53
- Cables and Connectors 54
- Cisco PA-MC-2T3+ 55
- Configuring the T3 Controller 58
- • show controllers t3 1/0/0 83
- Checking the Configuration 85
- Configuring T1 Lines 96
- • t1-line-number is 1–28 98
- OL-3526-05 103
- Terminating a BER Test 109
- Checking the Configuration 112
- Cisco 7200 Series Routers 114
- Cisco 7301 Routers 114
- Cisco 7401ASR Routers 115
- PA- MC-2T 3+: 116
- Using the show diag Command 117
- Cisco 7301 Router 119
- • show controllers 122
Prodotti e manuali riguardandi Gateway/Controller Cisco 3526
Gateway/Controller Cisco DPC3829 Specifiche
(100 pagine)
(100 pagine)
Gateway/Controller Cisco WAG200G Guida Utente
(39 pagine)
(39 pagine)
Gateway/Controller Cisco AS5400XM - Universal Gateway Voice High-Density Easy Order Bundle Manuale Utente
(26 pagine)
(26 pagine)
(33 pagine)
Gateway/Controller Cisco VG350 Manuale Utente
(41 pagine)
(41 pagine)
Gateway/Controller Cisco AS5400XM - Universal Gateway Voice High-Density Easy Order Bundle Manuale Utente
(38 pagine)
(38 pagine)
Gateway/Controller Cisco DPA 7610 Manuale Utente
(22 pagine)
(22 pagine)
Gateway/Controller Cisco MGBSX1 Guida Utente
(7 pagine)
(7 pagine)
Gateway/Controller Cisco DPA 7630 Manuale Utente
(12 pagine)
(12 pagine)
Gateway/Controller Cisco 3521 Manuale Utente
(17 pagine)
(17 pagine)
Gateway/Controller Cisco 3540 Manuale Utente
(13 pagine)
(13 pagine)
© 2020, manymanuals.it. Tutti i diritti riservati | 0.035 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commenti su questo manuale