Cisco XR 12410 Manuale Utente Pagina 210
- Pagina / 238
- Indice
- RISOLUZIONE PROBLEMI
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
Chapter 5 Maintaining the Router
Removing and Replacing Cards from the Chassis
5-38
Cisco XR 12410 and Cisco XR 12810 Router Installation Guide
OL-17441-01
Removing and Replacing Cards from the Line Card and RP Card
Cage
This section describes the procedures for removing and installing a router
processor (RP) card or a line card. The line card and RP card cage has 10 slots
(numbered 0 through 9, from left to right). Line cards are installed in slots 0
through 7; RPs are installed in slots 8 and
9 (see Figure 5-22).
Caution Handle all cards by the metal card carrier edges only; avoid touching the board or
any connector pins. After removing a card, carefully place it in an antistatic bag
or similar environment to protect it from ESD and dust in the optic ports
(fiber-optic line cards).
Use the following procedure to remove and replace a line card or RP from the card
cage:
Step 1 Disconnect any cables from the card.
Step 2 Remove the card:
a. Loosen the captive screws at the top and bottom of the front panel
(
Figure 5-23a).
b. Pivot the ejector levers to unseat the card from the backplane connector
(
Figure 5-23b.)
c. Slide the card out of the slot (Figure 5-23c) and place it directly into an
antistatic bag or other ESD-preventive container.
Step 3 Replace the card by reversing the procedures in Steps 1 and 2.
- Router Installation Guide 1
- CONTENTS 5
- B Site Log B-1 9
- Contents 10
- OL-17441-01 10
- Changes to This Document 11
- Audience 12
- Document Organization 12
- Document Conventions 13
- Product Overview 15
- AC and DC Power Subsystems 19
- Figure 1-4 AC PEM Components 20
- DC Power Supplies 21
- • 2 alarm cards 23
- Clock Scheduler Card 24
- Alarm Cards and Alarm Display 25
- Line Cards 28
- Route Processor 28
- BITS 1 AUX CONSOLE 33
- PRP-3 LEDs 34
- PRP Memory Components 37
- PRP SDRAM 41
- PRP SRAM 42
- PRP NVRAM 42
- PRP Flash Memory 42
- PRP-3 Compact Flash 43
- XR 12000 Series Router 44
- Horizontal cable 46
- Blower Module 47
- Figure 1-18 Cooling Air Flow 48
- Preparing for Installation 51
- Safety Guidelines 52
- Laser Safety 53
- Lifting Guidelines 55
- Site Requirement Guidelines 56
- Enclosed Rack 57
- Open Rack 57
- Telco Rack 58
- Center-mount 59
- Rack-mount bracket 59
- (attached to rack posts) 59
- 18.95 in 61
- 26.533 in 61
- 7.735 in 61
- 18.798 in 61
- Air Flow Guidelines 62
- Power Connection Guidelines 63
- AC-Powered Routers 64
- DC-Powered Routers 65
- Figure 2-8 DC Power Cable Lug 66
- Site Wiring Guidelines 70
- PRP Auxiliary Port Signals 74
- PRP Console Port Signals 75
- PRP Ethernet Connections 76
- 8 7 6 5 4 3 2 1 78
- Transmission 80
- Installation Overview 85
- Required Tools and Equipment 86
- 1 Front Door Latch 87
- Removing Power Supplies 89
- Removing DC PEMs 90
- Removing the Blower Module 91
- Verifying Rack Dimensions 99
- Reinstalling Power Supplies 109
- Reinstalling AC PEMs 110
- Reinstalling DC PEMs 111
- Air filter door 114
- Clock scheduler card 114
- FAST ETERNET 118
- Alarm display 125
- Troubleshooting Overview 132
- Identifying Startup Issues 134
- Figure 4-1 AC PEM Components 136
- Troubleshooting a DC PEM 140
- 1 3 4 52 6 146
- 1 3 4 52 146
- ETH 1ETH 0 148
- PRP Reset Switch 149
- PROCESSOR 150
- PRP-3 Alphanumeric LEDs 154
- Single PRP-3 Scenario 154
- Dual PRP-3 Scenario 156
- Troubleshooting Line Cards 159
- Figure 4-11 Cooling Air Flow 167
- Blower Module Operation 168
- Power Supply Operation 168
- Overtemperature Conditions 169
- Maintaining the Router 173
- Powering Off the Router 174
- OC-12/STM-4 ATM 178
- Subsystem Components 184
- Figure 5-7 AC PEM Components 186
- Figure 5-11) 192
- Rear panel 193
- AC horizontal trough 193
- DC horizontal trough 204
- Clear plastic covers 204
- Card Cage 212
- Technical Specifications 219
- • chassis only 220
- Router Specifications 224
- Site Log 225
- Appendix B Site Log 226
- Numerics 229
Prodotti e manuali riguardandi Hardware Cisco XR 12410
Hardware Cisco 3200 Series Manuale Utente
(60 pagine)
(60 pagine)
Hardware Cisco LINKSYS WMP600N Manuale Utente
(37 pagine)
(37 pagine)
Hardware Cisco MICA V110 Manuale Utente
(10 pagine)
(10 pagine)
Hardware Cisco IDTA153 Manuale Utente
(2 pagine)
(2 pagine)
Hardware Cisco OL-12812-01 Manuale Utente
(18 pagine)
(18 pagine)
Hardware Cisco 2600-DC Series Manuale Utente
(20 pagine)
(20 pagine)
Hardware Cisco 7300-6T3 Manuale Utente
(54 pagine)
(54 pagine)
Hardware Cisco 3545 MCU Manuale Utente
(56 pagine)
(56 pagine)
Hardware Cisco 3000 Manuale Utente
(16 pagine)
(16 pagine)
Hardware Cisco 7206VXR NPE-400 Manuale Utente
(22 pagine)
(22 pagine)
Hardware Cisco 3515 MCU12 Manuale Utente
(54 pagine)
(54 pagine)
Hardware Cisco 340 Manuale Utente
(62 pagine)
(62 pagine)
Hardware Cisco 2600XM Series Manuale Utente
(28 pagine)
(28 pagine)
Hardware Cisco 4000 Manuale Utente
(18 pagine)
(18 pagine)
Hardware Cisco OL-6109-01 Manuale Utente
(22 pagine)
(22 pagine)
Hardware Cisco 3515 MCU24 Manuale Utente
(44 pagine)
(44 pagine)
Hardware Cisco 3620 Manuale Utente
(12 pagine)
(12 pagine)
Hardware Cisco 350 Manuale Utente
(12 pagine)
(12 pagine)
Bos manuels
La liste des produits de Bos contient 57 les manuels et guides d'utilisation des modèles 49 dans les appareils de type 2
Commenti su questo manuale