Cisco NTP-E157 Manuale Utente
Navigare online o scaricare Manuale Utente per Switch di rete Cisco NTP-E157. Cisco NTP-E157 User`s manual [en] Manuale Utente
- Pagina / 167
- Indice
- SEGNALIBRI
- User’s Manual 1
- Trademarks 2
- Disclaimer 2
- WEEE Warning 2
- TABLE OF CONTENTS 3
- 1. Introduction 6
- 1.3 Product Features 7
- 1.4 Product Specification 10
- 2. Installation 18
- 2.1.2 Front / Rear Panel 21
- 2.1.3 Top View 24
- 2.1.4 LED Indicators 25
- 2.2 Install the Switch 30
- 2.2.2 DIN-Rail Mounting 31
- 1 2 3 4 5 6 33
- Power 2 Power 1 33
- - + - + 33
- Connect the fiber cable 37
- 3. Network Application 39
- 3.1 Rapid Ring Application 40
- 3.3 Dual Homing Application 41
- 4. Console Management 42
- Console login interface 44
- 4.4 CLI Management 45
- 4.5 Commands Level 46
- 5. Web-Based Management 47
- 5.2 Requirements 48
- 5.3 Logging on the switch 48
- 5.4 System 50
- 5.4.1 System Information 51
- 5.4.2 IP Configuration 52
- 5.4.3 DHCP Server 53
- 5.4.3.2 Client Entries 54
- 5.4.3.3 Port and IP Bindings 55
- 5.4.4 TFTP 56
- 5.4.4.3 Backup Configuration 57
- 5.4.5 System Event Log 58
- 5.4.6 Fault Relay Alarm 62
- 5.4.7 SNTP Configuration 63
- UTC Timezone: 64
- 5.4.8 IP Security 66
- 5.4.9 User Authentication 67
- 5.5 Port Management 68
- 5.5.2 Port Control 69
- 5.5.3 Port Trunk 70
- 5.5.3.1 Aggregator setting 71
- LACP disabled 72
- LACP enabled 73
- Switch 1 configuration 73
- Switch 2 configuration 74
- 5.5.3.3 State Activity 76
- 5.5.4 Port Mirroring 77
- 5.5.5 Rate Limiting 78
- 5.6 Protocol 79
- New Tagged Packet 81
- Original Ethernet 81
- Priority CFI VLAN ID 81
- 5.6.1.2 VLAN Configuration 82
- 5.6.1.3 Port-based VLAN 82
- 5.6.1.4 802.1Q VLAN 84
- Group Configuration 89
- 5.6.2 Rapid Spanning Tree 90
- 5.6.2.2 RSTP Parameters 92
- 5.6 2.3 Illustration of STP 94
- 5.6.2.5 Port Configuration 98
- 5.6.3 SNMP Configuration 100
- 5.6.3.2 Trap Configuration 101
- 5.6.3.3 SNMPV3 Configuration 102
- Context Table 102
- User Table 102
- Group Table 103
- Access Table 103
- MIBview Table 104
- 5.6.4 QoS Configuration 105
- 5.6.4.2 Port-based Priority 107
- 5.6.4.3 COS Configuration 107
- 5.6.4.4 TOS Configuration 108
- 5.6.5 IGMP Snooping 110
- Type Response Time 112
- Non-Member 113
- Delaying Member Idle Member 113
- 5.6.5.2 IGMP Configuration 114
- 5.6.6 X-Ring 115
- 5.6.6.4 X-Ring Configuration 117
- 5.7 Security 119
- 5.7.1.2 System Configuration 122
- 5.7.1.3 Port Configuration 123
- 5.7.1.4 Misc Configuration 124
- 5.7.2 MAC Address Table 125
- 5.7.2.2 MAC Filtering 126
- 5.7.2.3 All MAC Addresses 127
- 5.7.2.4 Multicast Filtering 128
- 5.8.1 Digital Input 129
- 5.8.2 Digital Output 130
- 5.9 Power over Ethernet 131
- 5.10 Factory Default 135
- 5.11 Save Configuration 135
- 5.12 System Reboot 136
- 6. Command Sets 137
- 6.2 Port Commands Set 139
- 6.3 Trunk Commands Set 141
- 6.4 VLAN Commands Set 142
- 6.6 QOS Commands Set 145
- 6.7 IGMP Commands Set 145
- 6.9 SNMP Commands Set 146
- 6.11 802.1x Commands Set 149
- 6.12 TFTP Commands Set 150
- 6.14 SNTP Commands Set 152
- 6.15 X-ring Commands Set 153
- 6.16 PoE Command Set 153
- 7. SWITCH OPERATION 155
- 7.5 Auto-Negotiation 156
- What is PoE? 157
- POWER SOURCING 158
- EQUIPMENT (PSE) 158
- POWER DEVIC 158
- The PoE Provision Process 159
- Start-up 160
- Operation 160
- 12345678 162
- Appendix B Troubles shooting 163
- EC Declaration of Conformity 164
Sommario
User’s Manual of ISW-1022M User’s Manual ISW-1022M ISW-1022MT 8-Port 10/100Mbps + 2 Gigabit TP/SFP Managed Industrial Switch ISW-1022MPT 8-
User’s Manual of ISW-1022M Series and ISW-1033MT 10 1.4 Product Specification 1.4.1 ISW-1022M / ISW-1022MT Product Specification Product ISW-1022M I
User’s Manual of ISW-1022M Series and ISW-1033MT 100 5.6.3 SNMP Configuration Simple Network Management Protocol (SNMP) is the protocol developed to m
User’s Manual of ISW-1022M Series and ISW-1033MT 101 before and click Remove. The strings of Public_RO and Private_RW are default strings. You can re
User’s Manual of ISW-1022M 5.6.3.3 SNMPV3 Configuration Configure the SNMP V3 function. Figure 5-45 SNMP V3 configuration interface – User Table
User’s Manual of ISW-1022M Series and ISW-1033MT Group Table Configure SNMP v3 group table. Figure 5-46 SNMP V3 configuration interface – Group T
User’s Manual of ISW-1022M Series and ISW-1033MT The page includes the following fields: Object Description Context Prefix: Set up the context name.
User’s Manual of ISW-1022M Series and ISW-1033MT 5.6.4 QoS Configuration Quality of Service (QoS) is an advanced traffic prioritization feature that a
User’s Manual of ISW-1022M Series and ISW-1033MT 5.6.4.1 QoS Policy and Priority Type Here you can choose to use an 8-4-2-1 queuing scheme or a strict
User’s Manual of ISW-1022M 5.6.4.2 Port-based Priority Configure the priority level for each port. With the drop-down selection item of Priority Type
User’s Manual of ISW-1022M Series and ISW-1033MT Figure 5-52 QoS Configuration – COS Priority The table includes the following fields: Object Descri
User’s Manual of ISW-1022M Series and ISW-1033MT Figure 5-53 QoS Configuration – TOS Priority The table includes the following fields: Object Descr
User’s Manual of ISW-1022M Series and ISW-1033MT 11 Management Functions Management Interface Console, Telnet, Web Browser, SNMP v1, v2c and v3 Port
User’s Manual of ISW-1022M Series and ISW-1033MT 5.6.5 IGMP Snooping 5.6.5.1 Theory The Internet Group Management Protocol (IGMP) lets host and route
User’s Manual of ISW-1022M Series and ISW-1033MT Figure 5-55 Multicast flooding Figure 5-56 IGMP Snooping multicast stream control 111
User’s Manual of ISW-1022M Series and ISW-1033MT IGMP Versions 1 and 2 Multicast groups allow members to join or leave at any time. IGMP provides the
User’s Manual of ISW-1022M Series and ISW-1033MT The states a computer will go through to join or to leave a multicast group are shown below: Non-Memb
User’s Manual of ISW-1022M Series and ISW-1033MT 5.6.5.2 IGMP Configuration The Industrial Switch support IP multicast, you can enable IGMP protocol o
User’s Manual of ISW-1022M Series and ISW-1033MT 5.6.6 X-Ring X-Ring provides a faster redundant recovery than Spanning Tree topology. The action is s
User’s Manual of ISW-1022M Series and ISW-1033MT 5.6.6.2 Coupling Ring Application In the network, it may have more than one X-Ring group. By using th
User’s Manual of ISW-1022M Series and ISW-1033MT In Dual Homing application architecture, the upper level switches need to enable the Rapid Spanning
User’s Manual of ISW-1022M Series and ISW-1033MT 1st & 2nd Ring Ports: Pull down the selection menu to assign the ports as the member ports. 1s
User’s Manual of ISW-1022M Series and ISW-1033MT 5.7 Security In Security page, it has three parts of setting 802.1x/Radius, Static MAC address,
User’s Manual of ISW-1022M Series and ISW-1033MT 12 CE EN61000-4-3, CE EN-61000-4-4, CE EN61000-4-5, CE EN61000-4-6, CE EN61000-4-8, CE EN61
User’s Manual of ISW-1022M Series and ISW-1033MT z Client—the device (workstation) that requests access to the LAN and switch services and responds t
User’s Manual of ISW-1022M Series and ISW-1033MT and the authentication server until authentication succeeds or fails. If the authentication succeeds,
User’s Manual of ISW-1022M Series and ISW-1033MT switch can retransmit the request. If no response is received from the server after the specified num
User’s Manual of ISW-1022M Series and ISW-1033MT 5.7.1.3 Port Configuration You can configure the 802.1x authentication state for each port. The state
User’s Manual of ISW-1022M Series and ISW-1033MT 5.7.1.4 Misc Configuration Figure 5-67 802.1x Misc Configuration interface The page includes the fo
User’s Manual of ISW-1022M Series and ISW-1033MT 5.7.2 MAC Address Table Use the MAC address table to ensure the port security. 5.7.2.1 Static MAC Ad
User’s Manual of ISW-1022M Series and ISW-1033MT 5.7.2.2 MAC Filtering By filtering MAC address, the switch can easily filter the pre-configured MAC a
User’s Manual of ISW-1022M Series and ISW-1033MT 5.7.2.3 All MAC Addresses You can view all of the MAC addresses learned by the selected port. Se
User’s Manual of ISW-1022M Series and ISW-1033MT 5.7.2.4 Multicast Filtering Multicasts are similar to broadcasts, they are sent to all end stations o
User’s Manual of ISW-1022M Series and ISW-1033MT 5.8 Digital Input/Output (ISW-1033MT) The 7 10/100TX + 3 10/100/1000T/100/1000 SFP Combo w/ X-Ring L2
User’s Manual of ISW-1022M Series and ISW-1033MT 13 Flow Control Back pressure for half duplex, IEEE 802.3x Pause Frame for full duplex LED System
User’s Manual of ISW-1022M Series and ISW-1033MT 5.8.2 Digital Output When First/Second Digital Output function is enabled, First Digital Output/Se
User’s Manual of ISW-1022M Series and ISW-1033MT 5.9 Power over Ethernet This segment shows the Power over Ethernet function (Only for ISW-1022MPT). P
User’s Manual of ISW-1022M Series and ISW-1033MT activates additional ports, as long as the aggregated power of the system is lower than the power lev
User’s Manual of ISW-1022M Series and ISW-1033MT AC Disconnect Tick this checkbox to monitor the AC impedance on the port terminals and removes power
User’s Manual of ISW-1022M Series and ISW-1033MT PD Classifications A PD may be classified by the PSE based on the classification information prov
User’s Manual of ISW-1022M Series and ISW-1033MT 5.10 Factory Default Reset switch to default configuration. Click Default to reset all configuration
User’s Manual of ISW-1022M Series and ISW-1033MT 5.12 System Reboot Reboot the switch in software reset. Click Reboot to reboot the system. Figure
User’s Manual of ISW-1022M Series and ISW-1033MT 6. Command Sets Commands Set List User EXEC E Privileged EXEC P Global configuratio
User’s Manual of ISW-1022M Series and ISW-1033MT [Password] (maximum 10 words) show admin P Show administrator information switch#show admin dhcpserv
User’s Manual of ISW-1022M Series and ISW-1033MT 6.2 Port Commands Set Commands Level Description Example interface fastEthernet [Portid] G Choos
User’s Manual of ISW-1022M Series and ISW-1033MT 14 Spanning Tree IEEE 802.1d Spanning Tree IEEE 802.1w Rapid Spanning Tree Link Aggregation Supports
User’s Manual of ISW-1022M Series and ISW-1033MT bandwidth out [Value] Set interface output bandwidth. Rate Range is from 100 kbps to 102400 kbpsor t
User’s Manual of ISW-1022M Series and ISW-1033MT 6.3 Trunk Commands Set Commands Level Description Example aggregator priority [1~65535] G Set port
User’s Manual of ISW-1022M Series and ISW-1033MT 6.4 VLAN Commands Set Commands Level Description Example vlan database P Enter VLAN configure mod
User’s Manual of ISW-1022M Series and ISW-1033MT tag [TaggedVID List] untag 5 tag 6-8 vlan 8021q trunk [PortNumber] access-link untag [UntaggedVID] V
User’s Manual of ISW-1022M Series and ISW-1033MT root switch within this interval, it recomputed the Spanning Tree Protocol (STP) topology.spanning-tr
User’s Manual of ISW-1022M Series and ISW-1033MT [True|False] on this interface. switch(config-if)#stp-admin-non-stp False show spanning-tree E D
User’s Manual of ISW-1022M Series and ISW-1033MT 6.8 MAC / Filter Table Commands Set Commands Level Description Example mac-address-table static hw
User’s Manual of ISW-1022M Series and ISW-1033MT trap-version [v1|v2c] Switch(config)# no snmp-server host 192.168.1.50 snmpv3 context-name [Context
User’s Manual of ISW-1022M Series and ISW-1033MT [Group Name ] security-level [NoAuthNoPriv|AuthNoPriv|AuthPriv] match-rule [Exact|Prifix] views
User’s Manual of ISW-1022M Series and ISW-1033MT 6.11 802.1x Commands Set Commands Level Description Example 8021x enable G Use the 802.1x global
User’s Manual of ISW-1022M Series and ISW-1033MT 15 Standards Compliance IEEE 802.3 10Base-T IEEE 802.3u 100Base-TX/100Base-FX IEEE 802.3z Gigabit S
User’s Manual of ISW-1022M Series and ISW-1033MT 8021x misc maxrequest [number] G Use the 802.1x misc max request global configuration command to set
User’s Manual of ISW-1022M Series and ISW-1033MT 6.13 SystemLog, SMTP and Event Commands Set Commands Level Description Example systemlog ip [IP
User’s Manual of ISW-1022M Series and ISW-1033MT log switch(config-if)#no event systemlog no event smpt I Disable port event for SMTP switch(config)#
User’s Manual of ISW-1022M Series and ISW-1033MT 6.15 X-ring Commands Set Commands Level Description Example ring enable G Enable X-ring switch(co
User’s Manual of ISW-1022M Series and ISW-1033MT system ac-disconnect [Enable | Disable] PoE Set PoE system AC Disconnect switch(poe)# system ac-disco
User’s Manual of ISW-1022M Series and ISW-1033MT 7. SWITCH OPERATION 7.1 Address Table The Switch is implemented with an address table. This address t
User’s Manual of ISW-1022M Series and ISW-1033MT 7.5 Auto-Negotiation The STP ports on the Switch have built-in "Auto-negotiation". This tec
User’s Manual of ISW-1022M Series and ISW-1033MT 8. POWER OVER ETHERNET OVERVIEW What is PoE? Based on the global standard IEEE 802.3af, PoE is a tec
User’s Manual of ISW-1022M Series and ISW-1033MT The data pairs are used. Since Ethernet pairs are transformer coupled at each end, it is possible to
User’s Manual of ISW-1022M Series and ISW-1033MT The PoE Provision Process While adding PoE support to networked devices is relatively painless, it sh
User’s Manual of ISW-1022M Series and ISW-1033MT 16 DI/DO 2 Digital Input (DI):Level 0: -30~2V Level 1: 10~30V Max. input current: 8mA 2 Digital Outp
User’s Manual of ISW-1022M Series and ISW-1033MT Start-up Once line detection and optional classification stages are completed, the PSE must switch f
User’s Manual of ISW-1022M Series and ISW-1033MT Appendix A—RJ-45 Pin Assignment A.1 Switch's RJ-45 Pin Assignments 1000Mbps, 1000Base T Conta
User’s Manual of ISW-1022M Series and ISW-1033MT The standard cable, RJ-45 pin assignment The standard RJ-45 receptacle/connector There are 8 wir
User’s Manual of ISW-1022M Series and ISW-1033MT Appendix B Troubles shooting Verify that is using the right power cord/adapter (DC 24-48V), plea
EC Declaration of Conformity For the following equipment: *Type of Product: 8-Port 10/100Mbps + 2G TP/SFP Managed Industrial Switch (-10~60 Degr
EC Declaration of Conformity For the following equipment: *Type of Product: 8-Port 10/100Mbps + 2G TP/SFP Industrial Ethernet Switch with 8 PoE
EC Declaration of Conformity For the following equipment: *Type of Product: 8-Port 10/100Mbps + 2G TP/SFP Managed Industrial Switch (-10~60 Degr
EC Declaration of Conformity For the following equipment: *Type of Product: 7-Port 10/100Mbps + 3G TP/SFP Managed Industrial Switch (-40~75 Degr
User’s Manual of ISW-1022M Series and ISW-1033MT 17 Security Support 100 entries of MAC address for static MAC and another 100 for MAC filterSupport
User’s Manual of ISW-1022M Series and ISW-1033MT 18 2. Installation In this paragraph, it will describe the Industrial Switch’s hardware spec, port,
User’s Manual of ISW-1022M Series and ISW-1033MT 19 ISW-1022MPT Managed Industrial Switch dimension (W x D x H) : 72mm x 105mm x 152mm Figure 2-2
User’s Manual of ISW-1022M Series and ISW-1033MT 2 Trademarks Copyright © PLANET Technology Corp. 2009. Contents subject to which revision without pri
User’s Manual of ISW-1022M Series and ISW-1033MT 20 ISW-1033MT Managed Industrial Switch dimension (W x D x H) : 72mm x 105mm x 152mm Figure 2-3
User’s Manual of ISW-1022M Series and ISW-1033MT 21 2.1.2 Front / Rear Panel The Front Panel and Rear Panel of the ISW-1022M / ISW-1022MT Managed Ind
User’s Manual of ISW-1022M Series and ISW-1033MT 22 The Front Panel and Rear Panel of the ISW-1022MPT Managed Industrial Switch are shown as below: F
User’s Manual of ISW-1022M Series and ISW-1033MT 23 The Front Panel and Rear Panel of the ISW1033MT Managed Industrial Switch are shown as below: Fi
User’s Manual of ISW-1022M Series and ISW-1033MT 24 2.1.3 Top View The top panel of the ISW-1022M series Managed Industrial Switch has one terminal bl
User’s Manual of ISW-1022M Series and ISW-1033MT 25 The top panel of the ISW-1033MT Managed Industrial Switch has one terminal block connector of two
User’s Manual of ISW-1022M Series and ISW-1033MT 26 10/100Base-TX Ports – Port-1 to Port-8 LED Color Status Meaning On A network device is de
User’s Manual of ISW-1022M Series and ISW-1033MT 27 On Power 1 is active. PWR1 Green Off Power 1 is inactive. On Power 2 is active. PWR2 Green O
User’s Manual of ISW-1022M Series and ISW-1033MT 28 ISW-1022MPT LED Indicators System LED Color Status Meaning On The switch unit is power on.
User’s Manual of ISW-1022M Series and ISW-1033MT 29 10/100/1000Base-T / SFP combo interface - Port-9, Port-10 LED Color Status Meaning On A ne
User’s Manual of ISW-1022M Series and ISW-1033MT 3 TABLE OF CONTENTS 1. INTRODUCTION ...
User’s Manual of ISW-1022M Series and ISW-1033MT 30 2.2 Install the Switch This section describes how to install your Managed Industrial Switch and ma
User’s Manual of ISW-1022M Series and ISW-1033MT 31 2.2.2 DIN-Rail Mounting The DIN-Rail is screwed on the Industrial Switch when out of factory. If t
User’s Manual of ISW-1022M Series and ISW-1033MT 32 2. Then, lightly push the DIN-Rail into the track. Figure 2-10 DIN-Rail mounting 3. Check if t
User’s Manual of ISW-1022M Series and ISW-1033MT 33 2.2.4 Wiring the Power Inputs The 6-contact terminal block connector on the top panel of ISW-1022M
User’s Manual of ISW-1022M Series and ISW-1033MT 34 2.2.5 Wiring the Fault Alarm Contact The fault alarm contacts are in the middle of the terminal bl
User’s Manual of ISW-1022M Series and ISW-1033MT 35 2.2.6 Wiring the Digital Inputs / Outputs (ISW-1033MT) There is another terminal block comprising
User’s Manual of ISW-1022M Series and ISW-1033MT 36 2.2.7 Installing the SFP transceiver The sections describe how to insert an SFP transceiver into a
User’s Manual of ISW-1022M Series and ISW-1033MT 37 Connect the fiber cable 1. Attach the duplex LC connector on the network cable into the SFP tr
User’s Manual of ISW-1022M Series and ISW-1033MT 38 3. Turn the handle of the MGB module to horizontal. 4. Pull out the module gently through the h
User’s Manual of ISW-1022M Series and ISW-1033MT 39 3. Network Application This chapter provides some sample applications to help user to have more
User’s Manual of ISW-1022M Series and ISW-1033MT 4 5.4.1 System Information...
User’s Manual of ISW-1022M Series and ISW-1033MT 40 3.1 Rapid Ring Application The industrial Switch supports the Rapid Ring (X-Ring) protocol that ca
User’s Manual of ISW-1022M Series and ISW-1033MT 41 3.3 Dual Homing Application Dual Homing function is to prevent the connection lose from between
User’s Manual of ISW-1022M Series and ISW-1033MT 42 4. Console Management 4.1 Connecting to the Console Port The supplied cable which one end is RS-
User’s Manual of ISW-1022M Series and ISW-1033MT 43 4.3 Login in the Console Interface To configure the system, connect a serial cable to a COM port
User’s Manual of ISW-1022M Series and ISW-1033MT 44 Once the terminal has connected to the device, power on the ISW Managed Industrial Switch, the ter
User’s Manual of ISW-1022M Series and ISW-1033MT 45 4.4 CLI Management The system supports the console management—CLI command. After you log in on to
User’s Manual of ISW-1022M Series and ISW-1033MT 46 4.5 Commands Level Modes Access Method Prompt Exit Method About This Mode1 User EXEC Begin a s
User’s Manual of ISW-1022M Series and ISW-1033MT 47 5. Web-Based Management This section introduces the configuration and functions of the Web-Based
User’s Manual of ISW-1022M Series and ISW-1033MT 48 5.2 Requirements • Workstations of subscribers running Windows 98/ME, NT4.0, 2000/2003/XP, MAC OS
User’s Manual of ISW-1022M Series and ISW-1033MT 49 Default User name: admin Default Password: admin 3. After entering the username and password,
User’s Manual of ISW-1022M Series and ISW-1033MT 5 6.7 IGMP COMMANDS SET...
User’s Manual of ISW-1022M Series and ISW-1033MT 50 5.4 System Use the System menu items to display and configure basic administrative details of the
User’s Manual of ISW-1022M Series and ISW-1033MT 51 5.4.1 System Information User can assign the system name, description, location and contact person
User’s Manual of ISW-1022M Series and ISW-1033MT 52 5.4.2 IP Configuration The switch is a network device which needs to be assigned an IP address for
User’s Manual of ISW-1022M Series and ISW-1033MT 53 DNS1: Assign the primary DNS IP address. DNS2: Assign the secondary DNS IP address. 5.4.3 DHCP S
User’s Manual of ISW-1022M Series and ISW-1033MT 54 Low IP Address: Type in an IP address. Low IP address is the beginning of the dynamic IP range. Fo
User’s Manual of ISW-1022M Series and ISW-1033MT 55 5.4.3.3 Port and IP Bindings Assign the dynamic IP address bound with the port to the connected cl
User’s Manual of ISW-1022M Series and ISW-1033MT 56 5.4.4 TFTP It provides the functions allowing the user to update the switch firmware via the Trivi
User’s Manual of ISW-1022M Series and ISW-1033MT 57 The page includes the following fields: Object Description TFTP Server IP Address: Type in the TF
User’s Manual of ISW-1022M Series and ISW-1033MT 58 5.4.5 System Event Log This page allows the user to decide whether to send the system event log,
User’s Manual of ISW-1022M Series and ISW-1033MT 59 The page includes the following fields: Object Description Syslog Client Mode: Select the system
User’s Manual of ISW-1022M Series and ISW-1033MT 6 1. Introduction The PLANET Layer 2 Managed Industrial Switch series - ISW-1022M series and ISW-10
User’s Manual of ISW-1022M Series and ISW-1033MT 60 The page includes the following fields: Object Description Email Alert: With this function being
User’s Manual of ISW-1022M Series and ISW-1033MT 61 5.4.5.3 System Event Log—Event Configuration Having ticked the Syslog/SMTP checkboxes, the event l
User’s Manual of ISW-1022M Series and ISW-1033MT 62 Device warm start: When the device executes warm start, the system will issue the event log/ema
User’s Manual of ISW-1022M Series and ISW-1033MT 63 The page includes the following fields: Object Description Power Failure: Tick the check box to
User’s Manual of ISW-1022M Series and ISW-1033MT 64 Daylight Saving Time: This is used as a control switch to enable/disable daylight saving period an
User’s Manual of ISW-1022M Series and ISW-1033MT 65 ALA - Alaskan Standard -9 hours 3 am HAW - Hawaiian Standard -10 hours 2 am Nome, Alaska -11
User’s Manual of ISW-1022M Series and ISW-1033MT 66 5.4.8 IP Security IP security function allows the user to assign 10 specific IP addresses that hav
User’s Manual of ISW-1022M Series and ISW-1033MT 67 Remember to execute the “Save Configuration” action, otherwise the new configuration will lose w
User’s Manual of ISW-1022M Series and ISW-1033MT 68 5.5 Port Management 5.5.1 Port Statistics The following chart provides the current statistic info
User’s Manual of ISW-1022M Series and ISW-1033MT 69 Rx Bcast Packet: The counts of broadcast packet. Rx Mcast Packet: The counts of multicast packet.
User’s Manual of ISW-1022M Series and ISW-1033MT 7 uplink capability can guarantee the throughput to all nodes hooked into the network and distance ca
User’s Manual of ISW-1022M Series and ISW-1033MT 70 Speed: It is available for selecting when the Negotiation column is set as Force. When the Negotia
User’s Manual of ISW-1022M Series and ISW-1033MT 71 5.5.3.1 Aggregator setting This section provides Port Trunk-Aggregator Setting of each port from t
User’s Manual of ISW-1022M Series and ISW-1033MT 72 Work ports: This column field allows the user to type in the total number of active port up to fou
User’s Manual of ISW-1022M Series and ISW-1033MT 73 Figure 5-22 Static Trunking Group information The page includes the following fields: Object De
User’s Manual of ISW-1022M Series and ISW-1033MT 74 Figure 5-23 Aggregation Information of Switch 1 5. Click on the tab of Aggregator Information t
User’s Manual of ISW-1022M Series and ISW-1033MT 75 Figure 5-24 Switch 2 configuration interface 10. Click on the tab of Aggregator Information to
User’s Manual of ISW-1022M Series and ISW-1033MT 76 5.5.3.3 State Activity Having set up the LACP aggregator on the tab of Aggregator Setting, you can
User’s Manual of ISW-1022M Series and ISW-1033MT 77 5.5.4 Port Mirroring The Port mirroring is a method for monitor traffic in switched networks. Traf
User’s Manual of ISW-1022M Series and ISW-1033MT 78 5.5.5 Rate Limiting You can set up every port’s bandwidth rate and frame limitation type. Ingre
User’s Manual of ISW-1022M Series and ISW-1033MT 79 5.6 Protocol This section has the following items: 5.6.1 VLAN 5.6.2 Rapid Spanning Tree Proto
User’s Manual of ISW-1022M Series and ISW-1033MT 8 • IEEE 802.1d classic Spanning Tree Algorithm • IEEE 802.1w Rapid Spanning Tree Protocol ¾ Rapid D
User’s Manual of ISW-1022M Series and ISW-1033MT 80 The tagging feature allows VLAN to span multiple 802.1Q-compliant switches through a single phy
User’s Manual of ISW-1022M Series and ISW-1033MT 81 Adding an IEEE802.1Q Tag Dest. Addr. Src. Addr. Length/E. type Data Old CRC Dest. Addr. Src
User’s Manual of ISW-1022M Series and ISW-1033MT 82 1 No matter what basis is used to uniquely identify end nodes and assign these nodes VLAN member
User’s Manual of ISW-1022M Series and ISW-1033MT 83 Figure 5-31 VLAN – Port Based interface Pull down the selection item and focus on Port Based t
User’s Manual of ISW-1022M Series and ISW-1033MT 84 Figure 5-33 VLAN—Port Based Edit/Delete interface Use Delete to delete the VLAN. Use Edit
User’s Manual of ISW-1022M Series and ISW-1033MT 85 802.1Q VLAN Port Configuration This page is used for configuring the Industrial Switch port VLA
User’s Manual of ISW-1022M Series and ISW-1033MT 86 。 Hybrid: The port belongs to VLANs, and each VLAN is user-defined as tagged or untagged (full 80
User’s Manual of ISW-1022M Series and ISW-1033MT 87 VLAN configuration data. This allows network devices to dynamically exchange VLAN configuration in
User’s Manual of ISW-1022M Series and ISW-1033MT 88 Access Link Because the access port doesn’t have an understanding of tagged frame, the column fie
User’s Manual of ISW-1022M Series and ISW-1033MT 89 Group Configuration Edit the existing VLAN Group. Select the VLAN group in the table list.
User’s Manual of ISW-1022M Series and ISW-1033MT 9 ¾ Management WEB-based, Telnet, Console Command Line management Access through SNMP v1, v2c
User’s Manual of ISW-1022M Series and ISW-1033MT 90 5.6.2 Rapid Spanning Tree The Rapid Spanning Tree Protocol (RSTP) is an evolution of the Spanning
User’s Manual of ISW-1022M Series and ISW-1033MT 91 The path cost to the root from the transmitting port The port identifier of the transmitting
User’s Manual of ISW-1022M Series and ISW-1033MT 92 A port transitions from one state to another as follows: From initialization (switch boot) to b
User’s Manual of ISW-1022M Series and ISW-1033MT 93 The following are the user-configurable RSTP parameters for the switch level: Parameter Descripti
User’s Manual of ISW-1022M Series and ISW-1033MT 94 User-Changeable STA Parameters The Switch’s factory default setting should cover the majority of i
User’s Manual of ISW-1022M Series and ISW-1033MT 95 block using the Port Priority and Port Cost settings is, however, relatively straight forward. Br
User’s Manual of ISW-1022M Series and ISW-1033MT 96 Mbps Fast Ethernet link (default port cost = 19). Gigabit ports could be used, but the port cost s
User’s Manual of ISW-1022M Series and ISW-1033MT 97 Priority (0-61440): The switch with the lowest value has the highest priority and is selected as t
User’s Manual of ISW-1022M Series and ISW-1033MT 98 5.6.2.5 Port Configuration This web page provides the port configuration interface for RSTP. You c
User’s Manual of ISW-1022M Series and ISW-1033MT 99 Admin P2P: The rapid state transitions possible within RSTP are dependent upon whether the port co
Prodotti e manuali riguardandi Switch di rete Cisco NTP-E157
(2 pagine)
(298 pagine)
(12 pagine)
(129 pagine)
(24 pagine)
(99 pagine)
(5 pagine) (105 pagine)
© 2020, manymanuals.it. Tutti i diritti riservati | 0.209 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commenti su questo manuale