Cisco 1750 - 1750 Router Guida di Installazione Pagina 36
- Pagina / 84
- Indice
- RISOLUZIONE PROBLEMI
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
Verifying Your Installation
x
Cisco 1750 Router Hardware Installation Guide
78-6169-02
Verifying Your Installation
You can verify that you have correctly installed the router by checking the
following LEDs:
• PWR (front panel)—On when power is being supplied to the router.
• OK (front panel)—On when the router software is loaded and functional.
Blinking means that the router is performing a power-on self-test (POST).
• ETH ACT (front panel)—Blinking when there is network traffic on the local
Ethernet LAN.
• SLOTØ, SLOT1, and SLOT2 (front panel)—Activity on PORTØ and PORT1
of each of these slots varies, depending on the type of WIC or VIC installed.
Refer to Table 4 in the “Cisco 1750 Router Overview” chapter for detailed
information on activity at different ports.
• SLOT 0 and SLOT 1 OK (rear panel)—On when a WIC or VIC is correctly
installed in the slot.
• SLOT 2 OK (rear panel)—On when a VIC is correctly installed in the slot.
• LINK (rear panel)—On when the router is correctly connected to the local
Ethernet LAN through the 10/100-Mbps Ethernet port.
Optional Installation Steps
This section describes the following installation steps that you might or might not
use, depending on your site and how you are configuring the router:
• Connecting a PC
• Connecting a Modem
• Wall-Mounting
- Cisco 1750 Router Hardware 1
- Installation Guide 1
- CONTENTS 5
- 3 Troubleshooting 3-i 6
- B Cabling Specifications B-i 6
- Contents 7
- Audience and Scope 10
- Organization 10
- Related Publications 10
- Conventions 11
- About This Guide 12
- 78-6169-02 12
- ¡Atención! 13
- Varning! 13
- Advarsel 13
- Commands 14
- Cisco 1750 Router Overview 15
- Key Features 16
- Rear-Panel Ports and LEDs 18
- Table 3 Rear Panel LEDs 19
- Front-Panel LEDs 20
- Router Memory 23
- Amounts of Memory 24
- Unpacking the Router 25
- Additional Required Equipment 25
- Installation 27
- Installing WICs and VICs 31
- Step 6 Tighten the screws 33
- Interface card 34
- Cisco 1750 35
- Verifying Your Installation 36
- Optional Installation Steps 36
- Connecting a PC 37
- Console port 38
- Light blue 38
- To PC or terminal 38
- Connecting a Modem 39
- Wall-Mounting 40
- Troubleshooting 43
- Recovering a Lost Password 44
- Resetting the Router 46
- Resetting the Password 47
- Problem Solving 48
- OK LED Diagnostics 49
- Troubleshooting WICs and VICs 50
- Troubleshooting ISDN 53
- Technical Specifications 57
- Cabling Specifications 59
- • With Class I 60
- • With Class II 60
- Console Cable and Adapters 61
- Pin 1 on one connector and 62
- VIC Cables and Pinouts 63
- Table 4 RJ-11 Pinout 64
- Table 5 E&M Pinouts 64
- 7 E-lead Signaling output 65
- 8 SG Signaling ground 65
- Pin Signal Description 65
- Data Modules 67
- Safety Information 68
- Opening the Chassis 69
- Locating Modules 71
- Removing a Mini-Flash Module 72
- Mini-Flash module slot 74
- 45 degrees 74
- Notched edge 74
- Closing the Chassis 77
- Figure 8 Closing the Chassis 78
Prodotti e manuali riguardandi Networking Cisco 1750 - 1750 Router
Networking Cisco 2821 - Integrated Services Router Unified Communications Bundle Manuale Utente
(3 pagine)
(3 pagine)
Networking Cisco WAE-7326-K9 Specifiche
(840 pagine)
(840 pagine)
Networking Cisco WRT120N Manuale Utente
(4 pagine)
(4 pagine)
Networking Cisco MGX-FRSM-2T3E3 Manuale Utente
(38 pagine)
(38 pagine)
Networking Cisco WGA54G Guida Utente
(23 pagine)
(23 pagine)
Networking Cisco 1812 Manuale Utente
(3 pagine)
(3 pagine)
Networking Cisco 675E Specifiche
(20 pagine)
(20 pagine)
Networking Cisco WGA54G Manuale Utente
(26 pagine)
(26 pagine)
Networking Cisco MC16S Specifiche
(70 pagine)
(70 pagine)
Bos manuels
La liste des produits de Bos contient 57 les manuels et guides d'utilisation des modèles 49 dans les appareils de type 2
Commenti su questo manuale