Cisco 3631 Specifiche Pagina 85
- Pagina / 198
- Indice
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
3-23
Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers
OL-1957-03
Chapter 3 Configuring with the Command-Line Interface
Configuring Inverse Multiplexing for ATM Interfaces
Configuring Inverse Multiplexing for ATM Interfaces
To configure an inverse multiplexing for ATM (IMA) interface, you must use configuration mode
(manual configuration). In this mode, you enter Cisco IOS commands at the router prompt.
Note Before you begin, disconnect all WAN cables from the router to keep it from trying to run the
AutoInstall process. The router tries to run AutoInstall whenever you power it on, if there is a WAN
connection on both ends and the router does not have a valid configuration file stored in nonvolatile
random-access memory (NVRAM) (for instance, when you add a new interface). It can take several
minutes for the router to determine that AutoInstall is not connected to a remote Transmission
Control Protocol/Internet Protocol (TCP/IP) host.
This section describes basic configuration, including enabling the interface and specifying IP routing.
Depending on your own requirements and the protocols you plan to route, you might also need to enter
other configuration commands.
Note The T1/E1 physical layer information is configured underneath an interface called interface atm.
The ATM interfaces (representing the individual T1/E1 interfaces) are automatically created
depending on the configuration of the individual T1/E1 interfaces. You cannot directly add or delete
these interfaces.
Each port can be used as an independent T1/E1 ATM port with all the properties and functionality of
ATM interfaces. When the port becomes part of an IMA group, its ATM functionality ceases. At the
same time, the IMA group can use ATM commands.
Note On the 8-port E1 or T1 network module, only four ATM layer interfaces can be operational at the
same time. All the interfaces can be activated (configured as “no shutdown”) but only four at a time
can be operational and pass network traffic.
Configuring the ATM T1/E1 Interface
To configure the ATM interface, follow this procedure:
Command Purpose
Step 1
Router> enable
Password: password
Router#
Enter enable mode. Enter the password.
You have entered enable mode when the prompt
changes to
Router#.
Step 2
Router# configure terminal
Enter configuration commands, one per line.
End with CNTL/Z.
Router(config)#
Enter global configuration mode. You have
entered global configuration mode when the
prompt changes to
Router(config)#.
- Software Configuration Guide 1
- CONTENTS 3
- A Configuration Examples A-1 8
- C Using the ROM Monitor C-1 9
- Contents 10
- OL-1957-03 10
- Objectives 11
- Audience 11
- Organization 12
- Document Conventions 12
- Additional Information 13
- Obtaining Documentation 16
- Documentation CD-ROM 17
- Ordering Documentation 17
- Documentation Feedback 17
- Cisco.com 18
- Technical Assistance Center 18
- Cisco IOS Software Basics 21
- Slot 0Slot 1 Power supply 25
- W1Slot 2 W0 26
- Console/AUX 26
- FastEthernet 0/0 26
- Slot W1 Slot W0 28
- Getting Help 33
- Understanding Command Modes 34
- Before Starting Your Router 37
- Configuring Global Parameters 38
- Frame Relay Encapsulation 44
- LAPB Encapsulation 44
- X.25 Encapsulation 45
- ATM-DXI Encapsulation 45
- SMDS Encapsulation 45
- Synchronous Configuration 46
- Asynchronous Configuration 48
- PPP Encapsulation 50
- ISDN BRI Line Configuration 51
- For data only 52
- For voice and data 52
- E1/T1 ISDN PRI Configuration 54
- T1 Channelized Mode 57
- Switched Mode 59
- Dedicated Mode 59
- Completing the Configuration 60
- • Power on the router 71
- Configuring ISDN BRI Lines 74
- Configuring T1 Interfaces 77
- Configuring E1 Interfaces 78
- Configuring Codec Complexity 80
- Default Configuration 81
- Configuring ATM Interfaces 82
- Configuring PVCs 83
- Configuring SVCs 84
- Configuring the IMA Interface 87
- Benefits 92
- Verifying ATM Configuration 94
- Serial Communication Channels 97
- Asynchronous Craft Port 98
- Serial Data Channel 98
- Configuring the AIC 100
- Accessing the AIC 102
- Configuring Alarms 103
- Verifying the IP Address 105
- Troubleshooting Tips 107
- Software Upgrade 107
- Configuration Examples 108
- Configuration Tasks 109
- Cisco 3600 Series Routers 111
- Cisco 3640 Router 112
- Prerequisites 113
- Configure the LAN Interface 117
- Configuration Example 120
- Restrictions 122
- Verifying ATM Configuration 124
- Saving Configuration Changes 127
- Where to Go Next 127
- Configuring Voice-over-IP 129
- Router SJ Configuration 135
- Router SLC Configuration 136
- • IMA-8T1 in 146
- • NM-4A/S 146
- • WIC-2A/S 146
- • WIC-1DSU-56k4 146
- With an Unnumbered IP Address 160
- Discrete Alarm 162
- Modem Calls 163
- Formatting Procedures 171
- File and Directory Operations 174
- Display File Content 176
- Copy Files 177
- Rename a File 179
- Create a New Directory 180
- Remove a Directory 181
- Using the ROM Monitor 183
- ROM Monitor Commands 184
- Command Descriptions 185
- Debugging Commands 187
- Using the xmodem Command 190
- Using the tftpdnld Command 190
- Entering the ROM Monitor Mode 192
- Numerics 193
Prodotti e manuali riguardandi Networking Cisco 3631
Networking Cisco 2650 - 2650 Router Specifiche
(266 pagine)
(266 pagine)
Networking Cisco SRW224 Manuale Utente
(5 pagine)
(5 pagine)
Networking Cisco 3800 Series Specifiche
(40 pagine)
(40 pagine)
Networking Cisco 11154 - CSS - Switch Specifiche
(148 pagine)
(148 pagine)
Networking Cisco 1802 Specifiche
(198 pagine)
(198 pagine)
Networking Cisco SOHO 71 Manuale Utente
(7 pagine)
(7 pagine)
Networking Cisco DPC3825 Manuale Utente
(109 pagine)
(109 pagine)
Networking Cisco EPC3825 Manuale Utente
(35 pagine)
(35 pagine)
Networking Cisco SRW208MP Manuale Utente
(14 pagine)
(14 pagine)
BenQ 18.5 wide LCD Monitor manuali
Manuali dei proprietari e guide per l'utente per Televisori e monitor BenQ 18.5 wide LCD Monitor.
We fornisce 2 manuali pdf BenQ 18.5 wide LCD Monitor per scaricare gratuitamente in base al tipo di documento: Manuale Utente
Benq 18.5 wide LCD Monitor Manuale Utente (1 pagine)
Marchio: Benq | Categoria: TVs & monitors | Dimensione: 0.20 MB |
Indice
Benq 18.5 wide LCD Monitor Manuale Utente (1 pagine)
Marchio: Benq | Categoria: TVs & monitors | Dimensione: 0.20 MB |
Indice
Più prodotti e manuali per Televisori e monitor BenQ
| Modelli | Tipo di Documento |
|---|---|
| GL2440 |
Manuale Utente
Инструкция BenQ GL2440HM,
39 pagine
|
| BL902TM |
Manuale Utente
BenQ BL902TM User manual,
38 pagine
|
| GL2240A |
Manuale Utente
BenQ GL2240 LCD Monitor,
1 pagine
|
| G2200WT |
Manuale Utente
Toimistouskottava työmyyrä,
1 pagine
|
| BL2201PT |
Manuale Utente
LCD-Monitor Benutzerhandbuch BL2201PT - PC,
45 pagine
|
| FP756-12ms |
Specifiche
BenQ FP756-12ms Specifications,
70 pagine
|
| BL902TM |
Manuale Utente
Monitor LCD Manual del usuario BL902TM,
40 pagine
|
| V2210 |
Manuale Utente
BenQ V2210 User manual,
57 pagine
|
| BL2201PT |
Manuale Utente
BenQ BL2201PT LCD Monitor,
1 pagine
|
| BL2201M |
Manuale Utente
LCD-Monitor Benutzerhandbuch BL2201M - PC,
41 pagine
|
| DV3250 |
Manuale Utente
DV3250 (32") Features,
1 pagine
|
| FP72E |
Manuale Utente
FP72E S/FP92E S Monitor LCD en color Manual del usuario,
40 pagine
|
| GL941M |
Manuale Utente
BenQ GL941M,
1 pagine
|
| GL2055A |
Manuale Utente
GL2055A Designed For Excellence,
1 pagine
|
| E900HDAP |
Manuale Utente
BenQ E900HDAP User manual,
36 pagine
|
| G2025HDA |
Manuale Utente
ÐнÑÑÑÑкÑÐ¸Ñ Ð´Ð»Ñ BenQ G2025HDA | 2. ÐаÑалÑнÑе ÑÐ²ÐµÐ´ÐµÐ½Ð¸Ñ Ð¾,
35 pagine
|
| FP567S |
Manuale Utente
BenQ FP567S User`s manual,
17 pagine
|
| G900HDA | Manuale Utente hardware, 1 pagine |
| BL902M |
Manuale Utente
LCD-Monitor Benutzerhandbuch BL902M - PC,
37 pagine
|
| XL Series |
Manuale Utente
BenQ Professional Gaming Monitors,
4 pagine
|
© 2020, manymanuals.it. Tutti i diritti riservati | 0.039 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commenti su questo manuale