Cisco Catalyst 8540 MSR Informazioni Techniche Pagina 6
- Pagina / 42
- Indice
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
Chapter 3 Initially Configuring the ATM Switch Router
Modifying the Physical Layer Configuration of an ATM Interface
3-6
ATM Switch Router Software Configuration Guide
78-6277-03, Cisco IOS Release 12.0(13)W5(19)
Manually Setting the ATM Address
To configure a new ATM address that replaces the previous ATM address when running IISP software
only, see the “Configuring the ATM Address” section on page 10-5.
To configure a new ATM address that replaces the previous ATM address and generates a new PNNI
node ID and peer group ID, see the “Configuring an ATM Address and PNNI Node Level” section on
page 10-10.
ModifyingthePhysicalLayerConfigurationofanATMInterface
Each of the ATM switch router’s physical interfaces has a default configuration, listed in Chapter 17,
“Configuring Interfaces.” You can accept the defaults, or you can override them by reconfiguring the
physical interface.
The following example describes modifying an OC-3c interface from the default settings to the
following:
• Disable scrambling cell-payload.
• Disable scrambling STS-streaming.
• Change Synchronous Optical Network (SONET) mode of operation from Synchronous Time Stamp
level 3c (STS-3c) mode to Synchronous Transfer Module level 1 (STM-1).
To change the configuration of the example interface, perform the following steps, beginning in global
configuration mode:
Example
The following example shows how to disable cell-payload scrambling and STS-stream scrambling and
changes the SONET mode of operation to Synchronous Digital Hierarchy/Synchronous Transfer
Module 1 (SDH/STM-1) of OC-3c physical interface ATM 0/0/0:
Switch(config)# interface atm 0/0/0
Switch(config-if)# no scrambling cell-payload
Switch(config-if)# no scrambling sts-stream
Switch(config-if)# sonet stm-1
To change any of the other physical interface default configurations, refer to the commands in the
ATM Switch Router Command Reference publication.
Command Purpose
Step 1
Switch(config)# interface atm card/subcard/port
Switch(config-if)#
Selects the physical interface to be configured.
Step 2
Switch(config-if)# no scrambling cell-payload Disables cell-payload scrambling.
Step 3
Switch(config-if)# no scrambling sts-stream Disables STS-stream scrambling.
Step 4
Switch(config-if)# sonet stm-1 Configures SONET mode as SDH/STM-1.
- Configuration Prerequisites 2
- Configuring the BOOTP Server 4
- Configuring the ATM Address 5
- Configuring the IP Interface 7
- Displaying the IP Address 8
- Configuring Network Clocking 10
- Examples 11
- LightStream 1010) 12
- NCDP Network Example 14
- Enabling NCDP 15
- Configuring Network Routing 18
- OIR Test (Catalyst 8540 MSR) 20
- (Catalyst 8540 MSR) 28
- Configuring SNMP and RMON 32
- Storing the Configuration 32
- Testing the Configuration 32
- Confirming the ATM Address 37
Prodotti e manuali riguardandi Networking Cisco Catalyst 8540 MSR
Networking Cisco 2516 Manuale Utente
(26 pagine)
(26 pagine)
Networking Cisco RPM-XF Specifiche
(25 pagine)
(25 pagine)
Networking Cisco 675E Manuale Utente
(14 pagine)
(14 pagine)
Networking Cisco 3200 Series Manuale Utente
(14 pagine)
(14 pagine)
Networking Cisco WS-C2916M-XL Manuale Utente
(14 pagine)
(14 pagine)
Networking Cisco 2525 Manuale Utente
(4 pagine)
(4 pagine)
Networking Cisco WRT300N Manuale Utente
(3 pagine)
(3 pagine)
Networking Cisco MGX-FRSM-2CT3 Specifiche
(629 pagine)
(629 pagine)
Networking Cisco 3200 Series Specifiche
(94 pagine)
(94 pagine)
Networking Cisco 10008 Guida di Installazione
(48 pagine)
(48 pagine)
Networking Cisco 2950T-48 Manuale Utente
(30 pagine)
(30 pagine)
Networking Cisco 7246 - uBR Router Specifiche
(24 pagine)
(24 pagine)
Kenwood MFJ-286 manuali
Manuali dei proprietari e guide per l'utente per Microfoni Kenwood MFJ-286.
We fornisce 1 manuali pdf Kenwood MFJ-286 per scaricare gratuitamente in base al tipo di documento: Manuale Utente
Commenti su questo manuale