Cisco Cisco Aironet Wireless LAN Client Specifiche Pagina 77
- Pagina / 142
- Indice
- RISOLUZIONE PROBLEMI
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
5-15
Cisco Aironet Wireless LAN Client Adapters Installation and Configuration Guide for Linux
OL-1376-02
Chapter 5 Advanced Configuration
Overview
Go to the “Specifying a Home Network Configuration” section on page 5-16 for instructions on
activating a home network configuration.
Note If the Network Type parameter is set to Base Station, the 1, 2,
5.5, and 11 Mbps options cannot be selected.
Note If the Network Type parameter is set to No Base Station, your
client adapter’s data rate must match the data rate of the other
devices on the home network. Otherwise, your client adapter
might not be able to associate to them.
Network Type Specifies the type of network in which your client adapter is installed.
Default: Base Station
Network Type Description
No Base Station
(Ad Hoc)
Also referred to as peer to peer. Used to
set up a small network between two or
more devices. For example, a network
without a base station could be set up
between computers in a room so that
information can be shared.
Base Station
(Infrastructure)
Used to set up a connection to a wired
Ethernet network (through a base station).
Channel Specifies which frequency your client adapter uses as the channel for
communications. These channels conform to the IEEE 802.11 standard
for your regulatory domain.
• If your home network uses a base station, this parameter or is
disabled because it is set automatically and cannot be changed. The
client adapter uses the same frequency as the base station.
• If your home network does not use a base station, the channel of
the client adapter must be set to match the channel used by the
other clients with which you wish to communicate.
Range: Dependent on regulatory domain
Example: 1 to 11 (2412 to 2462 MHz) in North America.
Default: Dependent on regulatory domain
Example: 6 (2437 MHz) in North America.
Note See Appendix B, “Channels, Power Levels, and Antenna
Gains,” for a list of channel identifiers, channel center
frequencies, and regulatory domains for each channel.
Table 5-5 Home Networking Parameters (continued)
Parameter Description
- Guide for Linux 1
- CONTENTS 3
- Contents 4
- 5 Advanced Configuration 5-1 5
- 6 Diagnostics 6-1 5
- 7 Routine Procedures 7-1 5
- 8 Troubleshooting 8-1 6
- Japanese Translation D-7 7
- English Translation D-7 7
- Audience 10
- Organization 10
- Conventions 11
- Attention 12
- Avvertenza 12
- Advarsel 12
- Related Publications 13
- Obtaining Documentation 13
- Ordering Documentation 14
- Documentation Feedback 14
- Cisco.com 14
- Technical Assistance Center 15
- Cisco TAC Escalation Center 16
- Overview 17
- Terminology 18
- Parts of the Client Adapter 19
- Chapter 1 Overview 20
- Ad Hoc Wireless LAN 21
- Site Survey 22
- Preparing for Installation 25
- Safety Information 26
- Unpacking the Client Adapter 27
- System Requirements 27
- Site Requirements 28
- PCMCIA Installation 32
- Enter (Figure 3-3) 33
- Figure 3-7 Make All Screen 37
- Option 1 for Red Hat Systems 38
- Option 2 for Red Hat Systems 39
- Verifying Installation 41
- Inserting a PC Card 42
- Additional Procedures 44
- Opening the Client Utilities 46
- Selecting the Radio 47
- Enabling LEAP 52
- Using the Bcard Utility 53
- Finishing the Installation 54
- Enabling Security Features 55
- Server-Based Authentication 56
- Getting Started 56
- Changing the Password 56
- Entering a New WEP Key 57
- Selecting an Existing WEP Key 59
- Enabling WEP 59
- Message Integrity Check (MIC) 60
- Advanced Configuration 63
- Setting Enterprise Parameters 65
- Table 5-2 System Parameters 66
- Network Type Description 67
- Authentication Description 69
- Setting RF Network Parameters 71
- Data Rate Description 72
- Diagnostics 83
- Chapter 6 Diagnostics 85
- Receive Statistics 90
- Transmit Statistics 91
- Routine Procedures 93
- Ascertaining the ACU Version 94
- Selecting a Help Browser 95
- Loading New Firmware 95
- Uninstalling Manually 97
- Removing a PC Card 99
- Removing a PCI Client Adapter 99
- OL-1376-02 100
- Removing the Client Adapter 100
- Troubleshooting 101
- Using the Indicator LEDs 102
- Getting Help 104
- (Figure 8-3) 105
- Technical Specifications 107
- Power output 109
- Receiver sensitivity 109
- APPENDIX 113
- Channel Sets 114
- Translated Safety Warnings 117
- Warning for Laptop Users 119
- ¡Advertencia! 120
- Varning! 120
- Information 121
- Tested To Comply 122
- With FCC Standards 122
- FOR HOME OR OFFICE USE 122
- Canadian Compliance Statement 123
- Liechtenstein 124
- Japanese Translation 127
- English Translation 127
- GLOSSARY 129
- Glossary 130
- OL-1367-02 130
Prodotti e manuali riguardandi Networking Cisco Cisco Aironet Wireless LAN Client
Networking Cisco WRT610N Manuale Utente
(2 pagine)
(2 pagine)
Networking Cisco AVS 3120 Guida Utente
(14 pagine)
(14 pagine)
Networking Cisco 3515 MCU12 Manuale Utente
(9 pagine)
(9 pagine)
Networking Cisco SE2800 Manuale Utente
(22 pagine)
(22 pagine)
Networking Cisco MWR-1900-27 Specifiche
(448 pagine)
(448 pagine)
(4 pagine)
Networking Cisco 7513 Specifiche
(24 pagine)
(24 pagine)
Networking Cisco 7576 Manuale Utente
(44 pagine)
(44 pagine)
Networking Cisco Engine 611 Specifiche
(516 pagine)
(516 pagine)
(126 pagine)© 2020, manymanuals.it. Tutti i diritti riservati | 0.033 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commenti su questo manuale