Cisco IAD2431-1T1E1 Guida di Installazione Pagina 21
- Pagina / 28
- Indice
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
21
Configuring Digital Voice
To configure basic T1/E1 controller settings to support Point-to-Point Protocol (PPP), High-Level Data Link Control (HDLC),
or Frame Relay (FR), follow these steps, beginning in global configuration mode:
For additional information about configuring specific features, see the following references:
• For PPP, HDLC, or Frame Relay, consult the online master index for the Cisco IOS release you are using.
See the “Cisco IOS Software Documentation” section on page 4.
• For loopback diagnostics, or for configuring controller channel groups, channel-associated signaling (CAS) voice groups,
or time-division multiplexing (TDM) cross-connects, refer to the Cisco IAD2430 Series Integrated Access Devices Software
Configuration Guide.
See “Hardware Installation Guide” section on page 3.
Step 9
Router(config)# exit
Exits configuration mode.
Step 10
Router# show controller t1/e1 1/0
Verifies the controller configuration.
Command Description
Step 1
Router(config)# controller t1/e1 1/0
Enters controller configuration mode by controller number.
Step 2
Router(config-ctrl)# mode cas
Configures channel-associated signaling.
Step 3
Router(config-ctrl-cas)# framing esf
Configures framing.
Step 4
Router(config-ctrl-cas)# linecode b8zs
Configures line encoding format.
Step 5
Router(config-ctrl-cas)# framing {sf | esf}
If necessary, changes the DS1 link framing format. The default
is SuperFrame (sf).
Step 6
Router(config-ctrl-cas)# ds0-group 1 timeslots
1-24 type e&m-immediate-start
Configures the DS0 group.
Step 7
Repeat Steps 3 through 6 for each additional DS0
group.
Configures additional DS0 groups on the T1/E1 interface. You
can configure as many as 24 DS0 groups on a T1/E1.
Step 8
Router(config-ctrl-cas)# exit
Exits controller configuration mode.
Step 9
Router(config-ctrl)# no shutdown
Activates the T1/E1 controller.
Step 10
Router(config-ctrl)# exit
Exits controller configuration mode.
Step 11
Router(config)# exit
Exits configuration mode.
Step 12
Router# show controller t1/e1 1/0
Verifies the controller configuration.
Command Description
- Quick Start Guide 1
- Duration of Hardware Warranty 2
- 2 Related Documentation 3
- Software Configuration Guide 4
- Release Notes 4
- Cisco IAD2430-24FXS 5
- Cisco IAD2431-8FXS 5
- Cisco IAD2431-16FXS 5
- 8882488828 6
- 5 Installing the Chassis 7
- IMPORTANT SAFETY INSTRUCTIONS 8
- Chassis Installation Options 9
- Rack-Mounting the Chassis 10
- Wall-Mounting the Chassis 11
- CISCO IAD2400 12
- Grounding the Chassis 13
- Ground lug 14
- 7 Connecting Cables 15
- 8 Powering On the Cisco IAD 18
- Command Description 20
- Configuring Digital Voice 21
- Where to Go Next 22
- 10 Obtaining Documentation 23
- 11 Documentation Feedback 23
- Submitting a Service Request 25
Prodotti e manuali riguardandi Networking Cisco IAD2431-1T1E1
Networking Cisco 521 Manuale Utente
(12 pagine)
(12 pagine)
Networking Cisco NMH300 Guida di Installazione
(32 pagine)
(32 pagine)
Networking Cisco 7120-AT3 - 7120 Router Specifiche
(183 pagine)
(183 pagine)
Networking Cisco CTX2500 Informazioni Techniche
(30 pagine)
(30 pagine)
Networking Cisco WMA11B Guida Utente
(32 pagine)
(32 pagine)
Networking Cisco 7301 Informazioni Techniche
(40 pagine)
(40 pagine)
Networking Cisco ISE - Line Card ISE Specifiche
(82 pagine)
(82 pagine)
Networking Cisco SPA3102 Guida Utente
(100 pagine)
(100 pagine)
Networking Cisco 1005 - 1005 Router Guida Utente
(24 pagine)
(24 pagine)
Networking Cisco WRT150N Guida Utente
(90 pagine)
(90 pagine)
Networking Cisco PIX-515E Specifiche
(78 pagine)
(78 pagine)
(66 pagine)Bos manuels
La liste des produits de Bos contient 57 les manuels et guides d'utilisation des modèles 49 dans les appareils de type 2
Commenti su questo manuale