Cisco UCS-SPR-C220-V1 Specifiche Pagina 30
- Pagina / 134
- Indice
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
2-10
Cisco UCS C220 Server Installation and Service Guide
OL-25760-01
Chapter 2 Installing the Server
Initial Server Setup
Step 3 Set NIC mode, NIC redundancy, and choose whether to enable DHCP or set static network settings:
a. Press the Power button to boot the server. Watch for the prompt to press F8.
b. During bootup, press F8 when prompted to open the BIOS CIMC Configuration Utility.
c. Set the NIC mode to your choice for which ports to use to access the CIMC for server management
(see
Figure 1-3 on page 1-3 for identification of the ports):
• Shared LOM EXT (default)—This is shared LOM extended mode. This is the factory-default
setting, along with Active-active NIC redundancy and DHCP-enabled. With this mode, the shared
LOM and Cisco Card interfaces are both enabled.
In this mode, DHCP replies are returned to both the shared LOM ports and the Cisco card ports. If
the system determines that the Cisco card connection is not getting its IP address from a Cisco UCS
Manager system because the server is in standalone mode, further DHCP requests from the Cisco
card are disabled. Use the Cisco Card NIC mode if you want to connect to the CIMC through a Cisco
card in standalone mode.
• Dedicated—The dedicated management port is used to access the CIMC. You must select a NIC
redundancy and IP setting.
• Shared LOM—The 1-Gb Ethernet ports are used to access the CIMC. You must select a NIC
redundancy and IP setting.
• Cisco Card—The ports on an installed Cisco UCS virtual interface card (VIC) are used to access the
CIMC. You must select a NIC redundancy and IP setting.
Note The Cisco Card NIC mode is currently supported only with a Cisco UCS VIC that is installed in
PCIe slot 1. See also Special Considerations for Cisco UCS Virtual Interface Cards, page 3-37.
d. Use this utility to change the NIC redundancy to your preference. This server has three possible NIC
redundancy settings:
–
None—The Ethernet ports operate independently and do not fail over if there is a problem.
–
Active-standby—If an active Ethernet port fails, traffic fails over to a standby port.
–
Active-active—All Ethernet ports are utilized simultaneously. See NIC Modes and NIC
Redundancy Settings, page 2-12 for more information.
e. Choose whether to enable DHCP for dynamic network settings, or to enter static network settings.
Note Before you enable DHCP, your DHCP server must be preconfigured with the range of MAC
addresses for this server. The MAC address is printed on a label on the rear of the server. This
server has a range of six MAC addresses assigned to the CIMC. The MAC address printed on
the label is the beginning of the range of six contiguous MAC addresses.
f. Optional: Use this utility to make VLAN settings, and to set a default CIMC user password.
Note Changes to the settings take effect after approximately 45 seconds. Refresh with F5 and wait
until the new settings appear before you reboot the server in the next step.
g. Press F10 to save your settings and reboot the server.
- Cisco UCS C220 M3 Server 1
- CONTENTS 3
- Contents 4
- Related Documentation 7
- Organization 7
- Audience 8
- Documentation Feedback 8
- Conventions 8
- Varoitus 9
- Attention 9
- Avvertenza 9
- ¡Advertencia! 10
- Varning! 10
- Advarsel 11
- Overview 15
- HDD1 HDD2 HDD3 HDD4 16
- Summary of Server Features 17
- Chapter 1 Overview 19
- 6. SAS = serial attached SCSI 19
- Installing the Server 21
- Installation Guidelines 23
- Rack Requirements 24
- Equipment Requirements 24
- Slide Rail Adjustment Range 24
- Statement 1006 25
- Initial Server Setup 29
- System BIOS and CIMC Firmware 33
- Accessing the System BIOS 34
- Service Headers and Jumpers 35
- Maintaining the Server 41
- Status LEDs and Buttons 42
- Rear Panel LEDs and Buttons 44
- Internal Diagnostic LEDs 46
- Required Equipment 47
- Serial Number Location 50
- Color-Coded Touch Points 50
- Drive Population Guidelines 52
- Drive Replacement Procedure 53
- Replacing a Drive Backplane 54
- Replacing Fan Modules 56
- Replacing DIMMs 58
- Front of Server 59
- DIMM Replacement Procedure 61
- Replacing CPUs and Heatsinks 63
- CPU Replacement Procedure 64
- [Statement 1015] 70
- Replacing a Mezzanine Card 71
- Replacing a PCIe Riser 73
- 2 Rear alignment tabs – 74
- Replacing a PCIe Card 75
- Booting the Hypervisor VD 81
- Statement 1015 85
- Replacing Power Supplies 92
- Wiring a DC Power Supply 93
- Server Specifications 97
- Environmental Specifications 98
- Power Specifications 99
- 650W AC Power Supply 100
- 930W DC Power Supply 100
- Power Cord Specifications 101
- OL-25760-01 102
- AC Power Cord Illustrations 103
- Figure B-5 SFS-250V-10A-ID 104
- Figure B-6 SFS-250V-10A-IS 104
- Figure B-4 CAB-9K10A-EU 104
- Figure B-7 CAB-9K10A-IT 105
- Figure B-8 CAB-9K10A-SW 105
- Figure B-9 CAB-9K10A-UK 105
- Figure B-10 CAB-AC-250V/13A 106
- Figure B-11 CAB-N5K6A-NA 106
- Figure B-12 CAB-9K12A-NA 106
- APPENDIX 109
- RAID Backup Units 112
- RAID Controller Migration 114
- Embedded MegaRAID Controller 115
- Updating the Windows Driver 121
- Linux Driver Installation 122
- RAID Controller Cabling 127
- Cisco UCS C220 Server Cabling 128
- Mezzanine-Style Card 129
- PCIe-Style Card 129
- LFF 4-Drive Backplane Cabling 130
- For More Information 131
Prodotti e manuali riguardandi Server Cisco UCS-SPR-C220-V1
Server Cisco UCS B230 M2 Specifiche
(30 pagine)
(30 pagine)
Server Cisco UCS B200 M3 Specifiche
(67 pagine)
(67 pagine)
Server Cisco UCS-SPR-C240-P1 Specifiche
(156 pagine)
(156 pagine)
Server Cisco 32369 Manuale Utente
(21 pagine)
(21 pagine)
Server Cisco Aironet 1040 Series Manuale Utente
(16 pagine)
(16 pagine)
Server Cisco UCS C210 M2 Manuale Utente
(28 pagine)
(28 pagine)
Server Cisco AS5400HPX Manuale Utente
(10 pagine)
(10 pagine)
Server Cisco UCS B200 M3 Specifiche
(33 pagine)
(33 pagine)
Server Cisco UCS C460 Manuale Utente
(54 pagine)
(54 pagine)
Server Cisco 6200 Guida Utente
(14 pagine)
(14 pagine)
Server Cisco UCS C24 Specifiche
(58 pagine)
(58 pagine)
Server Cisco UCS B200 M3 Specifiche
(39 pagine)
(39 pagine)
Server Cisco 3.3 Manuale Utente
(7 pagine)
(7 pagine)
Bos manuels
La liste des produits de Bos contient 57 les manuels et guides d'utilisation des modèles 49 dans les appareils de type 2
Commenti su questo manuale