Cisco Signaling Interface H.323 Guida Utente Pagina 69
- Pagina / 178
- Indice
- RISOLUZIONE PROBLEMI
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
5-3
Cisco H.323 Signaling Interface User Guide
OL-2156-04 Rev. A1
Chapter 5 Troubleshooting Cisco HSI Alarms
Retrieving Alarm Messages
Retrieving Alarm Messages
Alarms can be displayed in noncontinuous mode or in continuous mode.
Noncontinuous Mode
To display all current alarms, use the rtrv-alms MML command.
Figure 5-1 shows an example of an alarm message displayed with the rtrv-alms MML command
(noncontinuous mode). For more information about the rtrv-alms MML command, see Appendix A,
“MML User Interface and Command Reference.”
Figure 5-1 Sample Alarm Message
The example in Figure 5-1 shows a Cisco Public Switched Telephone Network (PSTN) Gateway
(PGW 2200) communication failure on the Cisco HSI that has the node ID H323-GW1. The resulting
message is an alarm with a major severity level.
Continuous Mode
To display the names of active alarms and new alarm events, use the rtrv-alms:cont MML command.
Table 5-3 defines the message components that are displayed when the rtrv-alms:cont MML command
is used. The following is sample output from this command. For more information about the
rtrv-alms:cont MML command, see Appendix A, “MML User Interface and Command Reference.”
GW Signaling Gateway 2000-12-05 14:19:22
M RTRV
"H323-GW1: 2000-11-27 11:25:12.259, ** ALM=\"VSC FAILURE\",SEV=MJ”
"H323-GW1: 2000-11-27 11:25:13.259, ALM=\"VSC FAILURE\",SEV=MJ”STATE=CLEARED
"H323-GW1: 2000-11-27 11:25:13.260, ** ALM=\"CONFIGURATION FAILURE\",SEV=MJ”
"H323-GW1: 2000-11-27 11:25:14.011, A^ ALM=\"ENDPOINT CHANNEL INTERFACE FAILURE\",SEV=IF”
"H323-GW1: 2000-11-27 11:25:14.012, A^ ALM=\"ENDPOINT CHANNEL INTERFACE FAILURE\",SEV=IF”
/* Listening for alarm events... (Ctrl-C to stop) */
"H323-GW1: 2000-11-27 11:25:13.259, ** ALM=\"VSC FAILURE\",SEV=MJ”
/* Ctrl-C pressed */
“H323-GW1:ALM=\”VSC FAILURE\”,SEV=MJ
Node ID
Alarm Category
Severity Level
STATE=CLEARED
Displayed only if state=cleared
- User Guide 1
- CONTENTS 3
- 4 Managing the Cisco HSI 4-1 5
- Contents 10
- OL-2156-04 Rev. A1 10
- Document Objectives 11
- Audience 11
- Document Organization 12
- Document Conventions 13
- Related Documentation 14
- Obtaining Documentation 15
- Ordering Documentation 16
- Documentation Feedback 16
- Cisco.com 16
- Technical Assistance Center 17
- Cisco TAC Escalation Center 18
- Introduction 19
- Cisco HSI Overview 19
- Cisco HSI System Description 20
- OAM Subsystem 21
- Call Control Subsystem 21
- Operational Environment 23
- Cisco HSI Recovery 23
- Cisco HSI System Limitations 23
- Installing the Cisco HSI 26
- 31
- Starting the Cisco HSI 34
- Stopping the Cisco HSI 34
- Configuring the Cisco HSI 34
- Upgrading the Cisco HSI 34
- Removing the Cisco HSI 35
- Provisioning the Cisco HSI 37
- MML Configuration Commands 38
- System Configuration Data 39
- Cisco HSI Configuration 40
- Dynamic System Data 41
- H.323 Stack Configuration 44
- MML Provisionable Data 45
- RAS Parameters 46
- Table 3-8 RAS Parameters 47
- H.245 Parameters 49
- Table 3-12 H.245 Modes 51
- Asymmetric Codec Treatment 52
- Empty Capability Set 52
- H.323 Hairpin 52
- T.38 Fax 53
- Managing the Cisco HSI 55
- Starting Call Processing 56
- Measurements 56
- Call-Related Measurements 57
- Table 4-2 Q.931 Counter Group 58
- Table 4-3 H.245 Counter Group 59
- Overload 60
- Overload Level 1 61
- Overload Level 2 61
- Overload Level 3 61
- Setting Overload Data 61
- Retrieving Overload Data 62
- Rotating Log Files 62
- Log Messages 63
- Logging Levels 64
- RADVision Logging 65
- Setting Gapping 65
- Retrieving Call Gapping Data 66
- Alarms Overview 67
- SNMP Trap Types 68
- Retrieving Alarm Messages 69
- Alarms List 71
- Troubleshooting 72
- EISUP_PATH_FAILURE 73
- GATEKEEPER_INTERFACE_FAILURE 74
- GENERAL_PROCESS_FAILURE 74
- IP_LINK_FAILURE 74
- LOW_DISK_SPACE 75
- OVERLOAD_LEVEL3 75
- VSC_FAILURE 76
- OVERLOAD_LEVEL2 77
- CONFIG_CHANGE 77
- GAPPED_CALL_NORMAL 79
- GAPPED_CALL_PRIORITY 79
- OVERLOAD_LEVEL1 80
- PROVISIONING_SESSION_TIMEOUT 81
- STOP_CALL_PROCESSING 81
- Detailed Logging 82
- MML Commands 84
- Starting an MML Session 85
- Batch Files 85
- Creating a Batch File 86
- Starting a Batch File 86
- MML Responses 87
- MML Help 88
- Quitting an MML Session 88
- MML Command Reference 88
- • All active MML sessions 110
- • CPU load 111
- • Disk space 111
- • Number of calls in setup 111
- Skeleton Configuration File 121
- APPENDIX 139
Prodotti e manuali riguardandi Networking Cisco Signaling Interface H.323
Networking Cisco PA-2E3 Specifiche
(68 pagine)
(68 pagine)
Networking Cisco DPC2100 Manuale Utente
(7 pagine)
(7 pagine)
Networking Cisco 3G MicroCell Manuale Utente
(32 pagine)
(32 pagine)
Networking Cisco 7576 Manuale Utente
(20 pagine)
(20 pagine)
Networking Cisco ME-C6524GS-8S Manuale Utente
(14 pagine)
(14 pagine)
Networking Cisco EPC2203 Manuale Utente
(38 pagine)
(38 pagine)
Networking Cisco WMP110 Manuale Utente
(20 pagine)
(20 pagine)
Networking Cisco 3745 Guida di Installazione
(28 pagine)
(28 pagine)
Networking Cisco 12012 Manuale Utente
(6 pagine)
(6 pagine)
Networking Cisco WAE-611-K9 Manuale Utente
(28 pagine)
(28 pagine)
Networking Cisco ONS 15327 Specifiche
(334 pagine)
(334 pagine)
Kenwood MFJ-286 manuali
Manuali dei proprietari e guide per l'utente per Microfoni Kenwood MFJ-286.
We fornisce 1 manuali pdf Kenwood MFJ-286 per scaricare gratuitamente in base al tipo di documento: Manuale Utente
Commenti su questo manuale