Cisco 15310-MA Guida alla Risoluzione dei Problemi Pagina 327
- Pagina / 380
- Indice
- RISOLUZIONE PROBLEMI
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
4-19
Cisco ONS 15310-CL and Cisco ONS 15310-MA Troubleshooting Guide, Release 9.0
78-18394-01
Chapter 4 Error Messages
EID-3068 The falling threshold must be between 1 and {0}. This is an invalid falling threshold entry.
The valid range is from 1 to the specified
value.
EID-3069 The rising threshold must be greater than or equal to the falling
threshold.
Refer to the error message text.
EID-3070 Error in data for ports {0} Exactly one VLAN must be marked
untagged for each port. These changes will not be applied.
CTC encountered data error for the
specified ports. Only one VLAN should be
marked untagged for each port.
EID-3071 An error occurred while retrieving the learned address list. Unable to retrieve the learned MAC address
from the NE.
EID-3072 An error occurred while clearing the learned address. Failure attempting to clear the learned
MAC address from a specific card or Ether
group.
EID-3073 An error occurred while clearing the selected rows. Failure attempting to clear the learned
MAC address from a specific card or Ether
group.
EID-3074 An error occurred while clearing the learned address list by
{0}.
Error encountered trying to clear the
learned MAC address from either a VLAN
or a port.
EID-3075 At least one row in the parameter column must be selected. Refer to the error message text.
EID-3076 CTC lost its connection with this node. The NE Setup Wizard
will exit.
Refer to the error message text.
EID-3077 No optical link was selected. Refer to the error message text.
EID-3078 An optical link could not be created. Refer to the error message text.
EID-3079 Defaults cannot be applied to the node. {0} CTC cannot apply the defaults to the
specified node.
EID-3080 CTC cannot navigate to the target tab.
{0}
CTC cannot go to the specified target tab.
EID-3081 The port type cannot be changed. Refer to the error message text.
EID-3082 The {0} extension byte cannot be changed. You cannot modify the specified extension
byte.
EID-3084 An error occurred while retrieving laser parameters for {0}. There is no card, or there was an internal
communications error when attempting to
get the laser parameters for the card.
EID-3085 No OSC Terminations were selected Select an OSC termination and proceed.
EID-3086 One or more Osc terminations could not be created. Refer to the error message text.
EID-3087 The OSC termination could not be edited. Refer to the error message text.
EID-3088 No {0} card is present to switch. No card of the specified type is available to
switch.
EID-3089 The {0} state cannot be used or changed when the {1} has
failed or is missing.
You cannot use or change the specified state
when the card is failed or missing.
Table 4-1 Error Messages (continued)
Error/Warning
ID Error/Warning Message Description
- Cisco ONS 15310-CL and 1
- Cisco ONS 15310-MA 1
- Troubleshooting Guide 1
- CONTENTS 3
- Contents 10
- 78-18394-01 10
- 4 Error Messages 4-1 21
- Revision History 27
- Document Objectives 28
- Audience 28
- Related Documentation 28
- Document Conventions 29
- Waarschuwing 30
- Varoitus 30
- Attention 30
- Avvertenza 31
- Advarsel 31
- ¡Advertencia! 31
- Varning! 31
- General Troubleshooting 37
- 1.1.1 Facility Loopback 38
- 1.1.2 Terminal Loopback 39
- 1.1.3 Hairpin Circuit 39
- 1.1.4 Cross-Connect Loopback 39
- Test the Facility Loopback 41
- Test the Electrical Cabling 42
- Test the Hairpin Circuit 43
- • Click Delete 64
- Loopcodes on DS1 Ports 65
- 1.5.1 FEAC Send Code 66
- Test the Ethernet Card 68
- Test the OC-N Card 80
- 1.7.2.2 Perform Manual Tests 93
- 1.7.3.1 True Automatic Mode 95
- 1.7.3.2 Manual Prompt Mode 95
- 1.7.5 Perform Loop Tests 98
- Reconfigure the Browser 103
- CTC Operation Troubleshooting 106
- 1.10.4 CTC Does Not Launch 108
- 1.10.12 DCC Connection Lost 115
- 1.11 Circuits and Timing 116
- Circuits and Timing 117
- 1.12 Fiber and Cabling 122
- Fiber and Cabling 123
- 87654321 12345678 124
- Figure 1-12 LAN Cable Layout 125
- Table 1-34 LAN Cable Pinout 125
- 1.13 Power and LED Tests 126
- Power and LED Tests 127
- Verify Card LED Operation 128
- Off-Load the Diagnostics File 128
- Alarm Troubleshooting 131
- 2.1.1 Critical Alarms (CR) 132
- 2.1.2 Major Alarms (MJ) 132
- 2.1.3 Minor Alarms (MN) 133
- 2.1.4 Not Alarmed Conditions 134
- 2.3 Alarm Logical Objects 140
- Alarm Logical Objects 141
- 2.5 Trouble Notifications 146
- 2.5.3 Severities 147
- 2.5.4 Alarm Hierarchy 147
- Trouble Notifications 148
- 2.6 Safety Summary 149
- 2.7 Alarm Procedures 150
- 2.7.2 AIS-L 151
- 2.7.3 AIS-P 151
- 2.7.4 AIS-V 152
- 2.7.5 ALS 152
- 2.7.6 APC-END 152
- 2.7.7 APSB 152
- 2.7.8 APSCDFLTK 153
- 2.7.9 APSCINCON 153
- 2.7.10 APSCM 153
- 2.7.11 APSCNMIS 154
- 2.7.12 APSIMP 154
- 2.7.13 APS-INV-PRIM 155
- 2.7.14 APSMM 155
- Clear the APSMM Alarm 156
- 2.7.15 APS-PRIM-FAC 157
- 2.7.16 APS-PRIM-SEC-MISM 157
- 2.7.17 AS-CMD 157
- Clear the AS-CMD Condition 158
- 2.7.18 AS-MT 159
- 2.7.19 AS-MT-OOG 159
- 2.7.20 AUD-LOG-LOSS 159
- 2.7.21 AUD-LOG-LOW 160
- 2.7.22 AUTOLSROFF 160
- 2.7.23 AUTORESET 160
- 2.7.24 AUTOSW-AIS 161
- 2.7.25 AUTOSW-LOP (STSMON) 162
- 2.7.26 AUTOSW-LOP (VT-MON) 162
- 2.7.27 AUTOSW-PDI 162
- 2.7.28 AUTOSW-SDBER 163
- 2.7.29 AUTOSW-SFBER 163
- 2.7.30 AUTOSW-UNEQ (STSMON) 164
- 2.7.31 AUTOSW-UNEQ (VT-MON) 164
- 2.7.32 BAT-FAIL 165
- 2.7.33 BERT-ENBL 166
- 2.7.34 BERT-SYNC-FAIL 166
- 2.7.35 BKUPMEMP 166
- 2.7.36 BLSROSYNC 167
- Alarm Procedures 168
- 2.7.38 CARLOSS (EQPT) 169
- 2.7.39 CARLOSS (ML100T) 170
- 2.7.40 CLDRESTART 171
- 2.7.41 COMIOXC 172
- 2.7.42 CONTBUS-CLK-A 173
- 2.7.43 CONTBUS-CLK-B 173
- 2.7.44 CONTBUS-DISABLED 174
- 2.7.45 CONTBUS-IO-A 175
- 2.7.46 CONTBUS-IO-B 175
- 2.7.47 CTNEQPT-PBPROT 176
- 2.7.48 CTNEQPT-PBWORK 177
- 2.7.49 DATA-CRC; 178
- 2.7.50 DATAFLT 178
- 2.7.51 DBOSYNC 179
- 2.7.52 DISCONNECTED 179
- 2.7.53 DS3-MISM 180
- 2.7.54 DUP-IPADDR 180
- 2.7.55 DUP-NODENAME 181
- 2.7.56 DUP-SHELF-ID 182
- 2.7.57 EHIBATVG 182
- 2.7.58 ELWBATVG 182
- 2.7.59 ENCAP-MISMATCH-P 183
- 2.7.60 EOC 184
- Clear the EOC Alarm 185
- 2.7.61 EOC-L 186
- 2.7.62 EQPT 187
- 2.7.63 EQPT-MISS 188
- 2.7.64 ERFI-P-CONN 188
- 2.7.65 ERFI-P-PAYLD 189
- 2.7.66 ERROR-CONFIG 189
- 2.7.67 ETH-LINKLOSS 190
- 2.7.68 EXCCOL 191
- 2.7.69 EXT 191
- 2.7.70 FAILTOSW 192
- 2.7.71 FAILTOSW-PATH 192
- 2.7.72 FAN 193
- 2.7.73 FAN-DEGRADE 193
- 2.7.74 FE-AIS 193
- 2.7.75 FE-DS1-MULTLOS 194
- 2.7.76 FE-DS1-NSA 194
- 2.7.77 FE-DS1-SA 195
- 2.7.78 FE-DS1-SNGLLOS 195
- 2.7.79 FE-DS3-NSA 196
- 2.7.80 FE-DS3-SA 196
- 2.7.81 FE-EQPT-NSA 197
- 2.7.82 FE-FRCDWKSWBK-SPAN 197
- 2.7.83 FE-FRCDWKSWPR-SPAN 198
- 2.7.84 FE-IDLE 198
- 2.7.85 FE-LOCKOUTOFPR-SPAN 198
- 2.7.86 FE-LOF 198
- 2.7.87 FE-LOS 199
- 2.7.88 FE-MANWKSWBK-SPAN 199
- 2.7.89 FE-MANWKSWPR-SPAN 199
- 2.7.90 FEPRLF 199
- 2.7.91 FORCED-REQ 200
- 2.7.92 FORCED-REQ-SPAN 200
- 2.7.93 FP-LINK-LOSS 201
- 2.7.94 FRCDSWTOINT 201
- 2.7.95 FRCDSWTOPRI 201
- 2.7.96 FRCDSWTOSEC 201
- 2.7.97 FRCDSWTOTHIRD 202
- 2.7.98 FRNGSYNC 202
- 2.7.99 FSTSYNC 202
- 2.7.100 FULLPASSTHR-BI 203
- 2.7.101 GFP-CSF 203
- 2.7.102 GFP-EX-MISMATCH 203
- 2.7.103 GFP-LFD 204
- 2.7.104 GFP-UP-MISMATCH 204
- 2.7.105 HELLO 205
- 2.7.106 HIBATVG 206
- 2.7.107 HI-LASERBIAS 206
- 2.7.108 HI-LASERTEMP 207
- 2.7.109 HI-RXPOWER 208
- 2.7.110 HITEMP 208
- 2.7.111 HI-TXPOWER 208
- 2.7.112 HLDOVRSYNC 209
- 2.7.113 I-HITEMP 210
- 2.7.114 IMPROPRMVL 211
- 2.7.115 INC-ISD 212
- 2.7.117 INCOMPATIBLE-SW 213
- 2.7.118 INHSWPR 213
- 2.7.119 INHSWWKG 214
- 2.7.120 INTRUSION-PSWD 214
- 2.7.121 INVMACADR 215
- 2.7.122 IOSCFGCOPY 215
- 2.7.123 ISIS-ADJ-FAIL 215
- Clear the ISIS-ADJ-FAIL Alarm 216
- 2.7.124 KB-PASSTHR 217
- 2.7.125 LASEREOL 217
- 2.7.126 LCAS-CRC 217
- 2.7.127 LCAS-RX-DNU 218
- 2.7.128 LCAS-RX-FAIL 219
- 2.7.129 LCAS-TX-ADD 219
- 2.7.130 LCAS-TX-DNU 220
- 2.7.131 LINK-KEEPALIVE 220
- 2.7.132 LKOUTPR-S 221
- 2.7.133 LOA 221
- 2.7.134 LOCKOUT-REQ 222
- 2.7.135 LOF (BITS) 222
- 2.7.136 LOF (DS1) 223
- 2.7.137 LOF (DS3) 224
- 2.7.138 LOF (EC1) 225
- 2.7.139 LOF (OCN) 225
- 2.7.140 LOF (STSTRM) 226
- 2.7.141 LOGBUFR90 226
- 2.7.142 LOGBUFROVFL 226
- 2.7.143 LO-LASERBIAS 227
- 2.7.144 LO-LASERTEMP 228
- 2.7.145 LOM 228
- 2.7.146 LOP-P 228
- 2.7.147 LOP-V 229
- 2.7.148 LO-RXPOWER 229
- Clear the LO-RXPOWER Alarm 230
- 2.7.149 LOS (BITS) 231
- 2.7.150 LOS (DS1) 231
- 2.7.151 LOS (DS3) 232
- Clear the LOS (DS3) Alarm 233
- 2.7.152 LOS (EC1) 234
- 2.7.153 LOS (FUDC) 235
- 2.7.154 LOS (OCN) 236
- 2.7.155 LO-TXPOWER 237
- 2.7.156 LPBKCRS 238
- 2.7.157 LPBKDS3FEAC 238
- 2.7.158 LPBKDS3FEAC-CMD 239
- 2.7.161 LPBKFACILITY (EC1) 240
- 2.7.162 LPBKFACILITY (OCN) 241
- 2.7.165 LPBKTERMINAL (EC1) 242
- 2.7.166 LPBKTERMINAL (OCN) 243
- 2.7.167 LWBATVG 243
- 2.7.168 MAN-REQ 244
- 2.7.169 MANRESET 244
- 2.7.170 MANSWTOINT 244
- 2.7.171 MANSWTOPRI 244
- 2.7.172 MANSWTOSEC 245
- 2.7.173 MANSWTOTHIRD 245
- 2.7.174 MANUAL-REQ-SPAN 245
- 2.7.175 MATECLK 246
- 2.7.176 MEA (EQPT) 246
- 2.7.177 MEA (FAN) 247
- 2.7.178 MEA (PPM) 248
- 2.7.179 MEA (SHELF) 248
- 2.7.180 MEM-GONE 248
- 2.7.181 MEM-LOW 248
- 2.7.182 MFGMEM 248
- 2.7.183 NO-CONFIG 249
- 2.7.184 NON-CISCO-PPM 249
- 2.7.185 NOT-AUTHENTICATED 250
- 2.7.186 OOU-TPT 250
- 2.7.187 OPEN-SLOT 250
- 2.7.188 PDI-P 251
- 2.7.189 PLM-P 252
- 2.7.190 PLM-V 253
- 2.7.191 PORT-MISMATCH 253
- 2.7.192 PRC-DUPID 254
- 2.7.193 PROTNA 254
- 2.7.194 PROV-MISMATCH 254
- 2.7.195 PWR-FAIL-A 255
- 2.7.196 PWR-FAIL-B 255
- 2.7.197 RAI 256
- 2.7.198 RFI-L 256
- 2.7.199 RFI-P 257
- 2.7.200 RFI-V 257
- 2.7.201 ROLL 258
- 2.7.202 ROLL-PEND 259
- 2.7.203 ROUTE-OVERFLOW 259
- 2.7.204 RPR-PASSTHR 259
- 2.7.205 RPRW 259
- 2.7.206 RUNCFG-SAVENEED 260
- 2.7.207 SD 260
- 2.7.208 SD-L 262
- 2.7.209 SD-P 263
- 2.7.210 SD-V 263
- 2.7.211 SF 264
- 2.7.212 SF-L 264
- 2.7.213 SF-P 265
- 2.7.214 SFTWDOWN 265
- 2.7.215 SF-V 265
- 2.7.216 SHELF-COMM-FAIL 266
- 2.7.217 SNTP-HOST 266
- 2.7.218 SQM 267
- 2.7.219 SSM-DUS 267
- 2.7.220 SSM-FAIL 267
- 2.7.221 SSM-LNC 268
- 2.7.222 SSM-OFF 268
- 2.7.223 SSM-PRC 268
- 2.7.224 SSM-PRS 269
- 2.7.225 SSM-RES 269
- 2.7.226 SSM-SDH-TN 269
- 2.7.227 SSM-SETS 269
- 2.7.228 SSM-SMC 269
- 2.7.229 SSM-ST2 270
- 2.7.230 SSM-ST3 270
- 2.7.231 SSM-ST3E 270
- 2.7.232 SSM-ST4 270
- 2.7.233 SSM-STU 271
- 2.7.234 SSM-TNC 271
- 2.7.235 SW-MISMATCH 271
- 2.7.236 SWMTXMOD-PROT 272
- 2.7.237 SWMTXMOD-WORK 272
- 2.7.238 SWTOPRI 273
- 2.7.239 SWTOSEC 273
- 2.7.240 SWTOTHIRD 273
- 2.7.241 SYNC-FREQ 274
- 2.7.242 SYNCPRI 274
- 2.7.243 SYNCSEC 275
- 2.7.244 SYNCTHIRD 275
- 2.7.245 SYSBOOT 276
- 2.7.246 TIM 276
- 2.7.247 TIM-MON 277
- 2.7.248 TIM-P 278
- 2.7.249 TIM-S 278
- 2.7.250 TIM-V 279
- 2.7.251 TPTFAIL 279
- 2.7.252 TX-AIS 280
- 2.7.253 TX-LOF 280
- 2.7.254 TX-RAI 281
- 2.7.255 UNEQ-P 281
- 2.7.256 UNEQ-V 283
- 2.7.257 UNQUAL-PPM 283
- 2.7.258 VCG-DEG 284
- 2.7.259 VCG-DOWN 284
- 2.8 DS-1 Line Alarms 285
- 2. The ACT LED turns on 286
- Initiate a Lock-On Command 288
- Physically Replace a Card 293
- Delete a Circuit 294
- Clear an EC-1 Port Loopback 296
- Transient Conditions 299
- 3.2 Trouble Notifications 301
- 3.3 Transient Conditions 302
- 3.3.37 WORK-QUEUE-FULL 308
- 3.3.38 WKSWBK 308
- 3.3.39 WKSWPR 308
- 3.3.40 WRMRESTART 308
- Error Messages 309
- Table 4-1 Error Messages 310
- Chapter 4 Error Messages 311
- Numerics 365
Prodotti e manuali riguardandi Networking Cisco 15310-MA
Networking Cisco XR 12000 Specifiche
(136 pagine)
(136 pagine)
Networking Cisco 2821 - Integrated Services Router Unified Communications Bundle Manuale Utente
(3 pagine)
(3 pagine)
Networking Cisco WAE-7326-K9 Specifiche
(840 pagine)
(840 pagine)
Networking Cisco WRT120N Manuale Utente
(4 pagine)
(4 pagine)
Networking Cisco MGX-FRSM-2T3E3 Manuale Utente
(38 pagine)
(38 pagine)
Networking Cisco WGA54G Guida Utente
(23 pagine)
(23 pagine)
Networking Cisco 1812 Manuale Utente
(3 pagine)
(3 pagine)
Networking Cisco 675E Specifiche
(20 pagine)
(20 pagine)
(46 pagine)© 2020, manymanuals.it. Tutti i diritti riservati | 0.039 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commenti su questo manuale